manualshive.com logo in svg

Canon ImageRunner 4045, Trouble Error Codes List

Share
Download
Canon ImageRunner 4045 Trouble Error Codes List Download Page 16

16 

 

8001 

Finisher) 
If the tray does not return to home position 
when the tray 1 shift motor is driven for 25 
seconds. If the tray does not move to 
other area when tray 1 shift motor is 
driven for 5 seconds. 

is faulty. 2. The wiring between the 
finisher controller PCB and tray 1 
shift motor is faulty. 3. The tray 
up/down mechanism is faulty. 4. The 
tray 1 shift motor (M107) is faulty. 5. 
The finisher controller PCB is faulty. 

E540-
8002 

Tray 1 shift area error 
The dangerous area is reached before the 
tray 1 paper surface sensor detects paper 
surface during the paper surface detection 
operation. A discontinuous area is 
detected during tray operation. 

1. The tray 1 shift area sensor PCB 
is faulty. 2. The wiring between the 
finisher controller PCB and tray 1 
shift motor is faulty. 3. The tray 
up/down mechanism is faulty. 4. The 
tray 1 shift motor (M107) is faulty. 5. 
The finisher controller PCB is faulty. 

E540-
8003 

Swing guide switch/Staple safety switch 
error 
The swing guide switch or staple safety 
switch is activated while the tray is 
operating. 

1. The tray 1 shift area sensor PCB 
is faulty. 2. The wiring between the 
finisher controller PCB and tray 1 
shift motor is faulty. 3. The tray 
up/down mechanism is faulty. 4. The 
tray 1 shift motor (M107) is faulty. 5. 
The finisher controller PCB is faulty. 

E540-
8004 

The tray 1 shift motor clock error 
The FG input cannot be detected when 
the tray 1 shift motor has been driven for 
0.2 second. 

1. The tray 1 shift area sensor PCB 
is faulty. 2. The wiring between the 
finisher controller PCB and tray 1 
shift motor is faulty. 3. The tray 
up/down mechanism is faulty. 4. The 
tray 1 shift motor (M107) is faulty. 5. 
The finisher controller PCB is faulty. 

E540-
8005 

The tray 1 shift motor speed error 
(Staple/Booklet Finisher) 
The lock detection signal turns OFF 150 
ms after the lock detection signal turned 
ON. 

1. The tray 1 shift area sensor PCB 
is faulty. 2. The wiring between the 
finisher controller PCB and tray 1 
shift motor is faulty. 3. The tray 
up/down mechanism is faulty. 4. The 
tray 1 shift motor (M107) is faulty. 5. 
The finisher controller PCB is faulty. 

E540-
8006 

The tray 1 shift motor acceleration error 
The lock detection signal does not turn 
ON when the tray 1 shift motor has been 
driven for 1 second. 

1. The tray 1 shift area sensor PCB 
is faulty. 2. The wiring between the 
finisher controller PCB and tray 1 
shift motor is faulty. 3. The tray 
up/down mechanism is faulty. 4. The 
tray 1 shift motor (M107) is faulty. 5. 
The finisher controller PCB is faulty. 

E540-
8007 

The tray 1 shift motor error 
The lock detection signal does not turn 

1. The tray 1 shift area sensor PCB 
is faulty. 2. The wiring between the 

Summary of Contents for ImageRunner 4045































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands