manualshive.com logo in svg

Canon ImageRunner 4045, Trouble Error Codes List

Share
Download
Canon ImageRunner 4045 Trouble Error Codes List Download Page 68

68 

 

faulty. 5. The Finisher Controller PCB is 
faulty. 

 

Code 

Description 

Remedy 

E540-
8004 

The Tray 1 Shift Motor clock error 
(Finisher-E1) 
The FG input cannot be detected when 
the Tray 1 Shift Motor has been driven for 
0.2 second. 

1. The Tray 1 Shift Area Sensor PCB 
is faulty. 2. The wiring between the 
Finisher Controller PCB and Tray 1 
Shift Motor is faulty. 3. The tray 
up/down mechanism is faulty. 4. The 
Tray 1 Shift Motor (M107) is faulty. 5. 
The Finisher Controller PCB is faulty 

E540-
8005 

The Tray 1 Shift Motor speed error 
(Finisher-E1) 
The lock detection signal turns OFF 150 
msec after the lock detection signal 
turned ON. 

1. The Tray 1 Shift Area Sensor PCB 
is faulty. 2. The wiring between the 
Finisher Controller PCB and Tray 1 
Shift Motor is faulty. 3. The tray 
up/down mechanism is faulty. 4. The 
Tray 1 Shift Motor (M107) is faulty. 5. 
The Finisher Controller PCB is faulty. 

E540-
8006 

The Tray 1 Shift Motor acceleration error 
(Finisher-E1) 
The lock detection signal does not turn 
ON when the Tray 1 Shift Motor has been 
driven for 1 second. 

1. The Tray 1 Shift Area Sensor PCB 
is faulty. 2. The wiring between the 
Finisher Controller PCB and Tray 1 
Shift Motor is faulty. 3. The tray 
up/down mechanism is faulty. 4. The 
Tray 1 Shift Motor (M107) is faulty. 5. 
The Finisher Controller PCB is faulty. 

E540-
8007 

The Tray 1 Shift Motor error (Finisher-E1) 
The lock detection signal does not turn 
OFF when the Tray 1 Shift Motor is at a 
stop. 

1. The Tray 1 Shift Area Sensor PCB 
is faulty. 2. The wiring between the 
Finisher Controller PCB and Tray 1 
Shift Motor is faulty. 3. The tray 
up/down mechanism is faulty. 4. The 
Tray 1 Shift Motor (M107) is faulty. 5. 
The Finisher Controller PCB is faulty. 

E542-
8001 

Tray 1 time out error (Finisher-E1) 
1. If the tray does not return to home 
position when the Tray 1 Shift Motor is 
driven for 25 seconds. 2. If the tray does 
not move to other area when Tray 2 Shift 
Motor is driven for 5 seconds. 

1. The Tray 2 shift area Sensor PCB 
is faulty. 2. The wiring between the 
Finisher Controller PCB and Tray 2 
Shift Motor is faulty. 3. The tray 
up/down mechanism is faulty. 4. The 
Tray 2 shift Motor (M105) is faulty. 5. 
The Finisher Controller PCB is faulty. 

E542-
8002 

Tray 2 shift area error (Finisher-E1) 
1. The upper limit area is reached before 
the Tray 2 Paper Surface Sensor 1 

1. The Tray 2 Shift Area Sensor PCB 
is faulty. 2. The wiring between the 
Finisher Controller PCB and Tray 2 

Summary of Contents for ImageRunner 4045































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands