manualshive.com logo in svg

Canon ImageRunner 4045, Trouble Error Codes List

Share
Download
Canon ImageRunner 4045 Trouble Error Codes List Download Page 7

7 

 

Code 

Description 

Remedy 

E227-
0003 

The reader unit power supply 
(24V) is faulty. 
At the end of a job, the 24V port is 
off. 

1. Disconnect and then connect the power 
supply harness connector.(J504/J3/J114) 2. 
Replace the Power Supply PCB (UN1). 

E227-
0004 

The reader unit power supply 
(24V) is faulty 
When a load is being driven, the 
24V port is off. 

1. Disconnect and then connect the power 
supply harness connector.(J504/J3/J114) 2. 
Replace the Power Supply PCB (UN1). 

E240-
0000 

Error in controller communication 
The serial communication error 
such as parity error or overrun 
error is constantly detected. 

1. Check the Connectors. 2. Replace the 
DC Controller PCB (UN2). 

E240-
0001 

Error in controller communication 
The serial communication error 
such as parity error or overrun 
error is detected while printing. 

1. Check the Connectors. 2. Replace the 
DC Controller PCB (UN2). 

E246-
0001 

System error 

Contact to the sales companies. 

0002 

of the CCD home position. 
The attempt to detect the home 
position fails when the CCD is 
moved back. 

flexible cable(Reader Controller PCB 
(UN4)-Main Controller PCB 2 (UN14)). 2. 
Replace the flexible cable. 3. Replace the 
CCD HP sensor (S11). 4. Replace the 
Polygon Motor (M11). 5. Replace the 
Reader Controller PCB (UN4). 6. Replace 
the Main Controller PCB 2 (UN14). 

E225-
0000 

The light intensity of the CCD is 
faulty. 
The light intensity of the CCD 
during shading is under the 
specified level. 

1. Disconnect and then connect the 
flexible cable. 2. Replace the flexible 
cable. 3. Replace the CCD Unit. 4. 
Replace the Reader Controller PCB 
(UN4). 5. Replace the Main Controller 
PCB 2 (UN14). 

E227-
0001 

The reader unit power supply 
(24V) is faulty. 
At time of power-on, the 24V port 
is off. 

1. Disconnect and then connect the power 
supply harness connector. (J504/J3/J114) 
2. Replace the Power Supply PCB (UN1). 

E227-
0002 

The reader unit power supply 
(24V) is faulty. 
At the start of a job, the 24V port 
is off. 

1. Disconnect and then connect the power 
supply harness connector.(J504/J3/J114) 
2. Replace the Power Supply PCB (UN1). 

 

  

Summary of Contents for ImageRunner 4045































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands