manualshive.com logo in svg

Canon ImageRunner 4045, Trouble Error Codes List

Share
Download
Canon ImageRunner 4045 Trouble Error Codes List Download Page 62

62 

 

Main Controller PCB 2 
communication error. 

Main Controller PCB 2. 

E354 

System error 

Contact to the sales companies. 

E355 

System error 

Contact to the sales companies. 

E400-
0001 

Communication error between 
Reader Controller PCB (PCB1) 
and DADF 
Reception error occurs at the 
time of communication 
between the Reader Controller 
PCB and the DADF 

1. Connection error between the DADF Driver 
PCB (PCB1) and the Reader Controller PCB 
(PCB1). 2. Failure of the DADF Driver PCB 
(PCB1). 3. Failure of the Reader Controller 
PCB (PCB1). 

E400-
0002 

Communication error between 
Reader Controller PCB (PCB1) 
and DADF 
Reception error occurs at the 
time of communication 
between the Reader Controller 
PCB and the DADF. 

1. Connection error between the DADF Driver 
PCB (PCB1) and the Reader Controller PCB 
(PCB1). 2. Failure of the DADF Driver PCB 
(PCB1). 3. Failure of the Reader Controller 
PCB (PCB1). 

E401-
0001 

Pickup Roller Unit lifting error 
The level of the Pickup Roller 
Unit Lifter HP Sensor (SR12) 
does not change within the 
specified period of time 
although the Pickup Roller Unit 
Lifter Motor (M10) is driven. 

1. Connector disconnection/open circuit of the 
Pickup Roller Unit Lifter HP Sensor (SR12). 2. 
Connector disconnection/open circuit of the 
Pickup Roller Unit Lifter Motor (M10). 3. Failure 
of the Pickup Roller Unit Lifter HP Sensor 
(SR12). 4. Failure of the Pickup Roller Unit 
Lifter Motor (M10). 

E401-
0002 

Pickup Roller Unit lifting error 
The level of the Pickup Roller 
Unit Lifter HP Sensor (SR12) 
does not change within the 
specified period of time 
although the Pickup Roller Unit 
Lifter Motor (M10) is driven. 

1. Connector disconnection/open circuit of the 
Pickup Roller Unit Lifter HP Sensor (SR12). 2. 
Connector disconnection/open circuit of the 
Pickup Roller Unit Lifter Motor (M10). 3. Failure 
of the Pickup Roller Unit Lifter HP Sensor 
(SR12). 4. Failure of the Pickup Roller Unit 
Lifter Motor (M10). 

E407-
0001 

Tray Lifter Motor (M8) error 
The Tray HP Sensor (SR13) is 
not turned ON or OFF within 
the specified period of time 
although the Tray Lifter Motor 
(M8) is driven. 

1. Connector disconnection/open circuit of the 
Tray HP Sensor (SR13). 2. Connector 
disconnection/open circuit of the Tray Lifter 
Motor (M8). 3. Failure of the Tray HP Sensor 
(SR13). 4. Failure of the Tray Lifter Motor (M8). 

E407-
0002 

Tray Lifter Motor (M8) error 
The Paper Surface Sensor 
(SR6) is not turned ON within 
the specified period of time 

1. Connector disconnection/open circuit of the 
Paper Surface Sensor (SR6). 2. Connector 
disconnection/open circuit of the Tray Lifter 
Motor (M8). 3. Failure of the Paper Face 

Summary of Contents for ImageRunner 4045































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands