manualshive.com logo in svg

Canon ImageRunner 4045, Trouble Error Codes List

Share
Download
Canon ImageRunner 4045 Trouble Error Codes List Download Page 33

33 

 

Controller PCB and the Main 
Controller PCB. 

E732-
8888 

Error in the reader type 
When a scanner for the different model 
is detected during the communication 
with the reader 

Replace to the proper reader. 

E732-
9999 

Detection of Reader 
The Reader is detected for the first time 
with the printer model. (On the user 
screen, only the message "Turn OFF 
and then ON the power again", instead 
of an error code, is displayed. It is 
recorded as an error log in Service 
Mode > DISPLAY > ERR.) 

 

E733-
0000 

Printer communication error 
Unable to communicate with printer at 
startup. 

1. Check the connection of the 
Connector with the printer. 2. Check 
the power of the printer (check if the 
initialization operation is executed at 
startup). 3. Replace the DC Controller 
or the Main Controller PCB. 

E733-
0001 

Printer communication error 
Communication error between the Main 
Controller and the DC Controller. 

1. Check the connection between the 
DC controller PCB (J210) and the 
main controller PCB2 (I8112). 2. 
Check the power of the printer (check 
if the initialization operation is 
executed at startup). 3. Replace the 
DC Controller or the Main Controller 
PCB 2. 

E733-
0002 

Printer communication error 
Communication error between the Main 
Controller and the DC Controller. 

1. Check the connection between the 
DC controller PCB (J210) and the 
main controller PCB2 (I8112). 2. 
Check the power of the printer (check 
if the initialization operation is 
executed at startup). 3. Replace the 
DC Controller or the Main Controller 
PCB 2. 

E733-
0010 

Printer communication error 
Error to detect printer vertical 
synchronous signal. 

1. Check the connection between the 
DC controller PCB (J210) and the 
main controller PCB2 (I8112). 2. 
Check the power of the printer (check 
if the initialization operation is 
executed at startup). 3. Replace the 
DC Controller or the Main Controller 

Summary of Contents for ImageRunner 4045































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands