manualshive.com logo in svg

Canon ImageRunner 4045, Trouble Error Codes List

Share
Download
Canon ImageRunner 4045 Trouble Error Codes List Download Page 52

52 

 

Duplex Driver side (J311) and the Transfer 
High Voltage side (J3061). (In addition, 
check that 24V is output.) 2. Check the 
connection of the Transfer High Voltage 
PCB (J3306). 3. Replace the ETB Unit. 4. 
Replace the Duplex Driver PCB (PCB4). 

E100-
11xx 

BD unlock error 
Locked state was not detected 
within the specified period of time 
at start-up. 

1. Check if the door is opened. Close the 
door. 2. Check the connection between the 
DC Controller PCB (PCB1) and the Laser 
Driver PCB (PCB35). DC Controller side: 
J471, J472, Laser Driver side: J5100, J5101, 
Relay Harness connection to Polygon Motor 
and BD PCB: J3011 3. Replace the Laser 
Scanner Unit. 4. Replace the Laser Driver 
PCB (PCB35). 5. Replace the DC Controller 
PCB (PCB1). NOTE: When condensation 
occurs inside of the machine or the Laser 
Scanner Unit, this error also occurs. When 
condensation occurs, leave the machine or 
the unit as it is until condensation 
disappears. (Use the machine or the unit in 
an environment where condensation does 
not occur.) 

E100-
12xx 

BD unlock error 
After the BD range was specified, 
lock was unlocked for 1 second or 
longer. 

1. Check if the door is opened. Close the 
door. 2. Check the connection between the 
DC Controller PCB (PCB1) and the Laser 
Driver PCB (PCB35). DC Controller side: 
J471, J472, Laser Driver side: J5100, J5101, 
Relay Harness connection to Polygon Motor 
and BD PCB: J3011 3. Replace the Laser 
Scanner Unit. 4. Replace the Laser Driver 
PCB (PCB35). 5. Replace the DC Controller 
PCB (PCB1). NOTE: When condensation 
occurs inside of the machine or the Laser 
Scanner Unit, this error also occurs. When 
condensation occurs, leave the machine or 
the unit as it is until condensation 
disappears. (Use the machine or the unit in 
an environment where condensation does 
not occur.) 

E100-
13xx 

Polygon Motor BD unlock error 
(Laser diode is not lit up/ failure of 
the BD PCB/power supply error, 
or condensation) 
During the Polygon speed 

1. Check if the door is opened. Close the 
door. 2. Check the connection between the 
DC Controller PCB (PCB1) and the Laser 
Driver PCB (PCB35). DC Controller side: 
J471, J472, Laser Driver side: J5100, J5101, 

Summary of Contents for ImageRunner 4045































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands