manualshive.com logo in svg

Canon ImageRunner 4045, Trouble Error Codes List

Share
Download
Canon ImageRunner 4045 Trouble Error Codes List Download Page 69

69 

 

detects the paper surface during paper 
surface detection operation. 2. A 
discontinuous area is detected during tray 
operation. 3. During evacuation operation, 
arrival at the area beyond the Tray 2 
Paper Surface Sensor 2 is detected 
before this Sensor detects paper surface. 

Shift Motor is faulty. 3. The tray 
up/down mechanism is faulty. 4. The 
Tray 2 Shift Motor (M105) is faulty. 5. 
The Finisher Controller PCB is faulty. 

E542-
8004 

The Tray 2 Shift Motor clock error 
(Finisher-E1) 
The FG input cannot be detected when 
the Tray 2 Shift Motor has been driven for 
0.2 second. 

1. The Tray 2 Shift Area Sensor PCB 
is faulty. 2. The wiring between the 
Finisher Controller PCB and Tray 2 
Shift Motor is faulty. 3. The tray 
up/down mechanism is faulty. 4. The 
Tray 2 Shift Motor (M105) is faulty. 5. 
The Finisher Controller PCB is faulty. 

E542-
8005 

The Tray 2 Shift Motor speed error 
(Finisher-E1) 
The lock detection signal turns OFF 150 
msec after the lock detection signal 
turned ON. 

1. The Tray 2 Shift Area Sensor PCB 
is faulty. 2. The wiring between the 
Finisher Controller PCB and Tray 2 
Shift Motor is faulty. 3. The tray 
up/down mechanism is faulty. 4. The 
Tray 2 Shift Motor (M105) is faulty. 5. 
The Finisher Controller PCB is faulty. 

E542-
8006 

The Tray 2 Shift Motor acceleration error 
(Finisher-E1) 
The lock detection signal does not turn 
ON when the Tray 2 Shift Motor has been 
driven for 1 second. 

1. The Tray 2 Shift Area Sensor PCB 
is faulty. 2. The wiring between the 
Finisher Controller PCB and Tray 2 
Shift Motor is faulty. 3. The tray 
up/down mechanism is faulty. 4. The 
Tray 2 Shift Motor (M105) is faulty. 5. 
The Finisher Controller PCB is faulty. 

E542-
8007 

The Tray 2 Shift Motor error (Finisher-E1) 
The lock detection signal does not turn 
OFF when the Tray 2 Shift Motor is at a 
stop. 

1. The Tray 2 Shift Area Sensor PCB 
is faulty. 2. The wiring between the 
Finisher Controller PCB and Tray 2 
Shift Motor is faulty. 3. The tray 
up/down mechanism is faulty. 4. The 
Tray 2 Shift Motor (M105) is faulty. 5. 
The Finisher Controller PCB is faulty. 

E551-
0011 

Error in the Power Supply Fan of the 
Insertion Unit 
The loch signal is detected for the 
specified times while the fan operates. 

1. The connector of the Fan (F1) is 
disconnected. 2. The wiring of the 
Fan (F1) is faulty. 3. The Fan (F1) is 
faulty. 4. The Insertion Unit Controller 
PCB is faulty. 

E551-
0021 

Error in the Power Supply Fan of the 
Paper Folding Unit 
The loch signal is detected for the 

1. The connector of the Fan (F1) is 
disconnected. 2. The wiring of the 
Fan (F1) is faulty. 3. The Fan (F1) is 

Summary of Contents for ImageRunner 4045































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands