manualshive.com logo in svg

Canon ImageRunner 4045, Trouble Error Codes List

Share
Download
Canon ImageRunner 4045 Trouble Error Codes List Download Page 19

19 

 

and cannot move from HP, it is 
detected as an error if the same 
symptom occurs again after the first 
retry. 

physically removed. 4. Check if the Shift 
Roller Release Sensor (S3) failure 
occurs. 

E567-
0001 

Shift Roller Release Motor fails to 
move from HP 
At initial rotation, when the Motor 
rotates for specified period of time 
and cannot move from HP, it is 
detected as an error if the same 
symptom occurs again after the first 
retry 

1. Check if the Motor (M5) Connector is 
physically removed. 2. Replace the Motor. 
3. Check if the Shift Roller Release 
Sensor (S3) Connector is physically 
removed. 4. Replace the Shift Roller 
Release Sensor (S3). 

E567-
0002 

Shift Roller Release Motor fails to 
return to HP 
At initial rotation, when the Motor 
rotates for specified period of time 
and cannot return to HP, it is 
detected as an error if the same 
symptom occurs again after the first 
retry. 

1. Check if the Motor (M5) Connector is 
physically removed. 2. Replace the Motor. 
3. Check if the Shift Roller Release 
Sensor (S3) Connector is physically 
removed. 4. Replace the Shift Roller 
Release Sensor (S3). 

E56F-
0001 

Entrance Roller Release/Stopper HP 
Motor fails to move from HP 
At initial rotation, when the Motor 
rotates for specified period of time 
and cannot move from HP, it is 
detected as an error if the same 
symptom occurs again after the first 
retry. 

1. Check if the Motor (M6) Connector is 
physically removed. 2. Replace the Motor. 
3. Check if the Entrance Roller 
Release/Stopper HP Sensor (S5) 
Connector is physically removed. 4. 
Replace the Entrance Roller 
Release/Stopper HP Sensor (S5). 

E56F-
0002 

Entrance Roller Release/Stopper HP 
Motor fails to return to HP 
At initial rotation, when the Motor 
rotates for specified period of time 
and cannot return to HP, it is 
detected as an error if the same 
symptom occurs again after the first 
retry. 

1. Check if the Motor (M6) Connector is 
physically removed. 2. Replace the Motor. 
3. Check if the Entrance Roller 
Release/Stopper HP Sensor (S5) 
Connector is physically removed. 4. 
Replace the Entrance Roller 
Release/Stopper HP Sensor (S5). 

E571-
0001 

Gripper Open/Close Motor fails to 
move from HP 
At initial rotation, when the Motor 
rotates for specified period of time 
and cannot move from HP, it is 
detected as an error if the same 
symptom occurs again after the first 
retry. 

1. Check if the Motor (M7) Connector is 
physically removed. 2. Replace the Motor. 
3. Check if the Gripper Arm HP Sensor 
(S13) Connector is physically removed. 4. 
Replace the Gripper Unit HP Sensor (S7). 

Summary of Contents for ImageRunner 4045































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands