manualshive.com logo in svg

Canon ImageRunner 4045, Trouble Error Codes List

Share
Download
Canon ImageRunner 4045 Trouble Error Codes List Download Page 36

36 

 

When lock signal failed to be 
detected for 15 sec while the 
Exhaust Fan (Rear) (FM3) is 
driven. * The same condition is 
detected after the error retry is 
performed. 

Exhaust Fan (Rear) (FM3). 3. Replace the 
DC Controller PCB (UN2). 

E805-
0002 

Failure of the Exhaust Fan (Front) 
(FM4) 
When lock signal is detected for 15 
sec while the Exhaust Fan (Front) 
(FM4) is stopped. * The same 
condition is detected after the error 
retry is performed. 

1. Check connection of the Connectors 
(J2009/J2501/J206). 2. Replace the 
Exhaust Fan (Front) (FM4). 3. Replace the 
DC Controller PCB (UN2). 

E805-
0003 

Unstable rotation of the Exhaust 
Fan (Front) (FM4) 
When lock signal failed to be 
detected for 15 sec while the 
Exhaust Fan (Front) (FM4) is 
driven. * The same condition is 
detected after the error retry is 
performed. 

1. Check connection of the Connectors 
(J2009/J2501/J206). 2. Replace the 
Exhaust Fan (Front) (FAN4). 3. Replace 
the DC Controller PCB (UN2). 

E806-
0000 

Failure of the Main Body Cooling 
Fan (FM6) 
When lock signal is detected for 5 
sec while the Main Body Cooling 
Fan (FM6) is stopped. *The same 
condition is detected after the error 
retry is performed. 

1. Check connection of the Connectors 
(J2210/J222). 2. Replace the Main Body 
Cooling Fan (FM6). 3. Replace the DC 
Controller PCB (UN2) 

E806-
0001 

Unstable rotation of the Main Body 
Cooling Fan (FM6 
When lock signal failed to be 
detected for 15 sec while the Main 
Body Cooling Fan (FM6) is driven. * 
The same condition is detected 
after the error retry is performed. 

1. Check connection of the Connectors 
(J2210/J222). 2. Replace the Main Body 
Cooling Fan (FM6). 3. Replace the DC 
Controller PCB (UN2). 

E806-
0002 

Failure of the Paper Cooling Fan 
(FM7) 
When lock signal is detected for 15 
sec while the Paper Cooling Fan 
(FM7) is stopped. *The same 
condition is detected after the error 
retry is performed. 

1. Check connection of the Connectors 
(J2209/J2509/J206). 2. Replace the Paper 
Cooling Fan (FM7). 3. Replace the DC 
Controller PCB (UN2). 

E806-

Unstable rotation of the Paper 

1. Check connection of the Connectors 

Summary of Contents for ImageRunner 4045































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands