manualshive.com logo in svg

Canon ImageRunner 4045, Trouble Error Codes List

Share
Download
Canon ImageRunner 4045 Trouble Error Codes List Download Page 47

47 

 

Check the loosening of screw on the 
Slider Pin and abrasion of the pin. 
Tighten the screw or replace the Slider 
Pin. 1-D-3. Replace the Primary 
Charging Assembly. 2. Replace the 
Main Driver PCB (PCB2). 3. Replace 
the DC Controller PCB (PCB1). 

E060-
0002 

Primary Charging Shutter HP close 
error 
The Primary Charging Shutter Sensor 
(PS94) detects that the shutter is 
closed although it is moved to the open 
position. 

1. Check the position of the Primary 
Charging Shutter and the Cleaning Pad. 
1-A. In the case that the Primary 
Charging Shutter and the Cleaning Pad 
fail to operate (stopped at HP at front 
side) 1-A-1. Check the connection of the 
Primary Charging Wire Cleaning Motor 
(M6). Motor side: J3017, J3060 (iR-ADV 
8xxx)/J3160 (iRADV 6xxx) (relay), PCB 
side: J3177 (relay), J107 (Main Driver 
PCB (PCB2)) 1-A-2. Replace the 
Primary Charging Wire Cleaning Motor 
(M6). 1-B. In the case that the Primary 
Charging Shutter and the Cleaning Pad 
are stopped at rear side (close 
operation position) 1-B-1. Check the 
connection of the Primary Charging 
Shutter Sensor (PS94). Sensor side: 
J2029, J3089 (relay), PCB side: J3088 
(relay), J114 (Main Driver PCB (PCB2)) 
1-B-2. Replace the Primary Charging 
Shutter Sensor (PS94). 1-C. In the case 
that the Primary Charging Shutter and 
the Cleaning Pad are stopped along the 
way 1-C-1. Check the loosening of 
screw on the Slider Pin and abrasion of 
the pin. Tighten the screw or replace the 
Slider Pin. 1-C-2. Replace the Primary 
Charging Assembly. 2. Replace the 
Main Driver PCB (PCB2). 3. Replace 
the DC Controller PCB (PCB1). 

E061-
0001 

Potential control error (VL) 
The measured value in the dark area 
(VL) d/-30V or higher than the 
target potential at potential control. 
NOTE: If the difference is somewhere 
b/-10V and less than 30V, 
alarm is indicated. 

1. Check the connection of the Pre-
exposure LED (connector connection, 
open circuit, the caught cable). 2. Check 
the installation of the Primary Charging 
Assembly (connector connection, open 
circuit, the caught cable). 3. Check the 
fixation state of the Drum and the Drum 

Summary of Contents for ImageRunner 4045































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands