BridgeTech VB20 User Manual Download Page 69

Page: 69 / 261

OTT Channel Configuration

Enabled:

If channel monitoring is enabled the 'Enabled' field will be check
marked.

Select

engine:

A number between 1 and 5 depending on license activated indicating
which OTT engine the channel uses.

Threshold:

The OTT threshold template assigned to the channel by the user
telling the system when to generate alarms.

VBC

thresholds:

The alarm threshold template used to configure when alarms are
generated towards the VBC server.

Name:

The channel name specified by the user

Manifest

URL:

The channel URL specified by the user

PROBE USERS' MANUAL VERSION 5.0

2014 © BRIDGE Technologies Co AS - Bentsebrugata 20 - N-0476 Oslo, Norway - tel: +47 22 38 51 00

www.bridgetech.tv

Summary of Contents for VB20






































































































































































































































































Search results

Summary of Contents for VB20

Reviews:

BridgeTech VB20, User Manual, Page: 69 / 261

Search results

Summary of Contents for VB20

Reviews: