manualshive.com logo in svg

BridgeTech VB20, User Manual, Page: 241 / 261

Share
Download
BridgeTech VB20 User Manual Download Page 241

6.18.2  Data - Software

It is possible to software upgrade a probe by importing the new software image file the 
same way an XML configuration is imported (from software version 4.5). When clicking 
the 

Go!

 button the software is copied to the probe, and clicking the 

Save flash

 button 

will store the new software to flash. Note that the probe must not be powered down 
during the flash save process. Flash save progress is indicated by progress bars. Note 
that the probe will reboot when the new software has been successfully stored in flash, 
and it will be unresponsive until reboot is completed.

  PROBE USERS' MANUAL VERSION 5.0

2014 © BRIDGE Technologies Co AS - Bentsebrugata 20 - N-0476 Oslo, Norway - tel: +47 22 38 51 00

 

- 

www.bridgetech.tv

242

Summary of Contents for VB20






































































































































































































































































Reviews:

No comments