manualshive.com logo in svg

BridgeTech VB20, User Manual, Page: 127 / 261

Share
Download
BridgeTech VB20 User Manual Download Page 127

6.9.6  ETR 290 - PID list

This view lists the PIDs of the currently active stream of the selected input. The PID list 
can be sorted by clicking a table column header.

The name of the current stream is displayed in addition to the two round-robin 
indicator icons when relevant: the time cycle icon and the lock icon. By clicking the 
lock icon the round-robin cycling is stopped or resumed. A DVB or ATSC icon indicates 
the analysis mode. The analysis mode is defined as part of the ETR thresholds.
By clicking the button 

Clear counters

 the minimum and maximum bitrates and the 

CC error counters will be reset. Note that this cannot be undone.
When clicking the blue information icon associated with a PID details concerning that 
PID will be displayed. All services referring to the PID are listed, and scrambling 
information is shown.

The following PID details are displayed:

  PROBE USERS' MANUAL VERSION 5.0

2014 © BRIDGE Technologies Co AS - Bentsebrugata 20 - N-0476 Oslo, Norway - tel: +47 22 38 51 00

 

- 

www.bridgetech.tv

128

Summary of Contents for VB20






































































































































































































































































Reviews:

No comments