BridgeTech VB20 User Manual Download Page 60

Page: 60 / 261

Post FEC

BER:

Bit error rate after Viterbi FEC
above specified threshold

Default: Enabled, severity
Major

MER:

Modulation Error Ratio above
specified threshold

Default: Enabled, severity
Major

SNR:

Signal to Noise Ratio below
specified threshold

Default: Enabled, severity
Major

Signal

strength:

Signal strength below specified
threshold

Default: Enabled, severity
Major

SFN meas:

Measurements to do with DVB-T/T2
SFN networks

Default: Enabled, severity
Major

Packet error

count:

Detection of one or more errored
packets after demodulator FEC

Default: Enabled, severity
Major

Centre

frequency:

Difference between received and
configured RF frequency exceeds
speficied threshold (VB262, VB252)

Default: Enabled, severity
Major

Symbol rate:

Difference between received and
configured symbol rate exceeds
specified threshold (VB262)

Default: Enabled, severity
Major

Post BCH

FER:

DVB-T/T2 BCH Frame Error Rate
exceeds speficied threshold
(VB252)

Default: Enabled, severity
Major

Interface

overflow:

Input interface overflow error

Default: Enabled, severity
Major

SYS (system) events

[Critical

system

errors]:

Enable this to view all critical
system errors

Default: Enabled, severity
Fatal

[System

errors]:

Enable this to view all system
errors

Default: Enabled, severity
Major

[System

info]:

Enable this to view system
information messages

Default: Enabled, severity OK

OTT alarms

The number

of profiles

changed:

The number of profiles flagged in
the manifest file changed

Default: Enabled, severity
Warning

Download

The download duration time

Default: Disabled, severity

PROBE USERS' MANUAL VERSION 5.0

2014 © BRIDGE Technologies Co AS - Bentsebrugata 20 - N-0476 Oslo, Norway - tel: +47 22 38 51 00

www.bridgetech.tv

Summary of Contents for VB20






































































































































































































































































Search results

Summary of Contents for VB20

Reviews:

BridgeTech VB20, User Manual, Page: 60 / 261

Search results

Summary of Contents for VB20

Reviews: