manualshive.com logo in svg

BridgeTech VB20, User Manual, Page: 147 / 261

Share
Download
BridgeTech VB20 User Manual Download Page 147

ETR Thresholds - Priority 3:

NIT:

Enable or disable alarming of Network Information Table errors.
Only relevant when DVB mode is selected.

NIT - Maximum 

interval Actual 

(ms):

The maximum allowed section repetition interval for the NIT 
Actual table.
Default: 10 s

NIT - Maximum 

interval Other 

(ms):

The maximum allowed section repetition interval for the NIT 
Other table.
Default: 10 s

NIT - Require 

network id:

If enabled the probe will require that the network ID found in the 
NIT matches the configured value.
Default: Disabled

NIT - Require 

original 

network id:

If enabled the probe will require that the original network ID 
found in the NIT matches the configured value.
Default: Disabled

NIT - Min. num. 

transport 

streams:

The minimum number of transport streams that must be 
present in the NIT. Set to 0 to disable this check.
Default: 0

NIT - Cable 

descriptor:

If set to 'Required' an alarm will be generated if a Cable 
descriptor is not present in the NIT for the monitored frequency. 
Similarly if set to 'Not allowed', an alarm will be generated if the 
Cable descriptor is present.
Default: Optional

NIT - Satellite 

descriptor:

If set to 'Required' an alarm will be generated if a Satellite 
descriptor is not present in the NIT for the monitored frequency. 
Similarly if set to 'Not allowed', an alarm will be generated if the 
Satellite descriptor is present.
Default: Optional

NIT - Terrestrial 

descriptor:

If set to 'Required' an alarm will be generated if a Terrestrial 
descriptor is not present in the NIT for the monitored frequency. 
Similarly if set to 'Not allowed', an alarm will be generated if the 
Terrestrial descriptor is present.
Default: Optional

NIT - Compare 

with reference 

NIT:

If enabled the NIT will be compared with the NIT on the 
reference frequency, and an alarm will be generated if a 
mismatch is found. The first frequency in the tuning list will be 
used as the reference frequency. Both the CRC values of the 
different sections and the number of sections must be identical.
Default: Disabled

SI Repetition 

Enable or disable alarming of SI Repetition Rate errors.

  PROBE USERS' MANUAL VERSION 5.0

2014 © BRIDGE Technologies Co AS - Bentsebrugata 20 - N-0476 Oslo, Norway - tel: +47 22 38 51 00

 

- 

www.bridgetech.tv

148

Summary of Contents for VB20






































































































































































































































































Reviews:

No comments