manualshive.com logo in svg

BridgeTech VB20, User Manual, Page: 57 / 261

Share
Download
BridgeTech VB20 User Manual Download Page 57

skip.

IAT >= 

err-

thresh:

The Inter-packet Arrival Time exceeds 
the error threshold

Default: Disabled, severity 
Error

IAT >= 

warn-

thresh:

The Inter-packet Arrival Time exceeds 
the warning threshold

Default: Disabled, severity 
Warning

MLR >= 

err-

thresh:

The Media Loss Rate exceeds the 
error-threshold

Default: Enabled, severity 
Error

MLR >= 

warn-

thresh:

The Media Loss Rate exceeds the 
warning-threshold

Default: Disabled, severity 
Warning

TTL 

changed:

The Time-To-Live field is changing

Default: Enabled, severity 
Error

TOS 

changed:

The Type-Of-Service field is changing

Default: Enabled, severity 
Error

Multiple 

mcast 

sources:

There are multiple multicast sources

Default: Enabled, severity 
Error

Mcast 

source 

changed:

The multicast source changed to one 
of the valid multicast sources specified 
by the operator.

Default: Enabled, severity 
Error

Bitrate 

overflow:

The stream bitrate exceeds the 
maximum bitrate Ethernet threshold 
value specified by the operator.

Default: Enabled, severity 
Error

Bitrate 

underflow

:

The stream bitrate goes below the 
minimum bitrate Ethernet threshold 
value specified by the operator.

Default: Enabled, severity 
Error

FSM alarms

Full service 

monitoring:

Enable to view all FSM alarms.

Default: Enabled, severity 
Major

ETR (ETR 290) alarms

TS Sync:

No TS Sync

Default: Enabled, severity 
Major

Sync byte:

Sync byte error

Default: Enabled, severity 
Major

PAT:

Program Association Table error

Default: Enabled, severity 
Major

  PROBE USERS' MANUAL VERSION 5.0

2014 © BRIDGE Technologies Co AS - Bentsebrugata 20 - N-0476 Oslo, Norway - tel: +47 22 38 51 00

 

- 

www.bridgetech.tv

58

Summary of Contents for VB20






































































































































































































































































Reviews:

No comments