manualshive.com logo in svg

BridgeTech VB20, User Manual, Page: 136 / 261

Share
Download
BridgeTech VB20 User Manual Download Page 136

6.9.11 ETR 290 - Compare

The 

Compare

 view is based on analysis performed by the ETSI TR 101 290 engine and 

will only be visible if the probe is licensed with the ETR 290 option.
The 

Compare

 view allows comparison of services or transport streams across 

different probe interfaces. Clicking 

Show streams

 results in a list of selectable 

transport streams and services, and clicking 

Show services

 results in a list of 

selectable services. For a transport stream to be selectable it must be ETR monitored. 
Note that the screen is not auto-refreshed, click the 

Compare

 tab to perform an active 

refresh.

  PROBE USERS' MANUAL VERSION 5.0

2014 © BRIDGE Technologies Co AS - Bentsebrugata 20 - N-0476 Oslo, Norway - tel: +47 22 38 51 00

 

- 

www.bridgetech.tv

137

Summary of Contents for VB20






































































































































































































































































Reviews:

No comments