Home
/
BridgeTech
/
VB20
/
User Manual

BridgeTech VB20, User Manual, Page: 113 / 261

Share

Page: 113 / 261

BridgeTech VB20 User Manual Download Page 113

6.8.7 Ethernet - Ethernet thresh.

Thresholds are used to determine when to actually raise an alarm. If the defined
threshold levels are exceeded for a parameter, an alarm will be raised. Ethernet
thresholds are also used to scale some graphs like the MediaWindow graphs. The
alarm level of each of these alarms is set in the

Alarms - Alarm setup

view. Note

that it is also possible to disable alarms in the

Alarms - Alarm setup

view.

There are two different ways of creating user-defined thresholds. To create a new
threshold template from scratch the operator should click the

Add new threshold

button. A pop-up window will appear allowing the user to define alarm conditions.
Another way of creating a user-defined threshold template is by highlighting one of the
threshold templates already defined and then click the

Duplicate highlighted

button.
Deleting a threshold template is done by highlighting the threshold template that
should be removed and clicking

Delete selected

. It is possible to delete or edit

several entries simultaneously. Several entries are selected by using the regular

Ctrl +

click

or

Shift + click

functionality. Click the

Edit

button to edit one or more selected

threshold templates.

PROBE USERS' MANUAL VERSION 5.0

2014 © BRIDGE Technologies Co AS - Bentsebrugata 20 - N-0476 Oslo, Norway - tel: +47 22 38 51 00

-

www.bridgetech.tv

114

«
...
111
112
113
114
115
...
»

Summary of Contents for VB20






































































































































































































































































Reviews:

No comments