manualshive.com logo in svg

BridgeTech VB20, User Manual, Page: 221 / 261

Share
Download
BridgeTech VB20 User Manual Download Page 221

6.17.3  Setup - Time

The time of the probe is used to timestamp events in the 

alarm list

. The local time is 

always presented just below the 

alarm list

.

The probe time should not be set manually if the probe is synchronising against a time 
server (refer to the 

Setup - Params

 view).

6.17.4  Setup - Ethernet

The Ethernet setup menu defines the Ethernet setup parameters for the management 
interface (eth2) and the data/video interface (eth0). The link statuses for the two 
interfaces are updated live to reflect the current settings. All changes except changes 
to 

Speed

, 

Medium

 and 

Duplex

 require a reboot to take effect. Rebooting the probe 

from this page is achieved by clicking the 

Reboot

 button after changes have been 

confirmed by clicking the 

Apply

 button. Click the 

IPv6 Settings

 button to access the 

  PROBE USERS' MANUAL VERSION 5.0

2014 © BRIDGE Technologies Co AS - Bentsebrugata 20 - N-0476 Oslo, Norway - tel: +47 22 38 51 00

 

- 

www.bridgetech.tv

222

Summary of Contents for VB20






































































































































































































































































Reviews:

No comments