BridgeTech VB20 User Manual Download Page 61

Page: 61 / 261

bitrate low:

exceeds the OTT bitrate threshold.
The bitrate threshold is part of the
OTT threshold template defined in
the

OTT – Thresholds

view. A

threshold template is assigned to a
stream in the

OTT – Setup

view.

Warning

Download

bitrate too

low:

The download duration time
exceeds the OTT chunk duration
time.

Default: Enabled, severity
Error

Manifest

size:

The manifest file size exceeds the
OTT manifest size threshold.

Default: Enabled, severity
Warning

Actual

bitrate:

The actual measured bitrate does
not match the profile bitrate
specified in the manifest file.

Default: Enabled, severity
Warning

Download

timeout:

The download time exceeds twice
the chunk duration time.

Default: Enabled, severity
Major

Address

resolve error:

Unable to resolve address name.

Default: Enabled, severity
Error

Connection

failed:

Connection failed.

Default: Enabled, severity
Error

Send error:

Could not send data to host.

Default: Enabled, severity
Error

Receive

error:

Could not receive data from host.

Default: Enabled, severity
Major

Empty reply:

Response did not contain any data
in body.

Default: Enabled, severity
Major

HTTP error:

Invalid HTTP response.

Default: Enabled, severity
Major

HTTP redirect

error:

HTTP 3xx redirection error

Default: Enabled, severity
Major

HTTP client

error:

HTTP 4xx client error

Default: Enabled, severity
Major

HTTP server

error:

HTTP 5xx server error

Default: Enabled, severity
Major

Static

manifest:

Manifest file unchanged for longer
than configured threshold.

Default: Enabled, severity
Major

Manifest

parse error:

Failed to parse manifest file. Invalid
format.

Default: Enabled, severity
Major

Unknown

manifest:

Cannot recognize manifest XML
format.

Default: Enabled, severity
Fatal

PROBE USERS' MANUAL VERSION 5.0

2014 © BRIDGE Technologies Co AS - Bentsebrugata 20 - N-0476 Oslo, Norway - tel: +47 22 38 51 00

www.bridgetech.tv

Summary of Contents for VB20






































































































































































































































































Search results

Summary of Contents for VB20

Reviews:

BridgeTech VB20, User Manual, Page: 61 / 261

Search results

Summary of Contents for VB20

Reviews: