1 689 989 000
2013-05-02
|
Robert Bosch GmbH
Decommissioning | EPS 200 | 47
en
7. Decommissioning
7.1
Relocation
Heed the following if the EPS 200 is to be relocated:
R
Disconnect the electrical connection.
R
Disconnect the pneumatic connection.
R
Drain test oil from the test oil tank (see section 6.2.5,
steps 1 to 8).
R
Replace the transport protection on the drive unit
(see section 4.3).
R
Only transport the EPS 200 in a crate.
When selling or transferring the EPS 200, all of the
documentation supplied must be included.
7.2
Scrapping
The test oil contained in the EPS 200 must be drained
before scrapping. The pipe filter at the flowmeter, the
intake filter in the test oil tank and the filter mats for
external extraction in the jet chamber unit must also be
removed and disposed of.
i
Oils are water polluting fluids and they must be
disposed of in accordance with waste disposal laws.
Test oil complying with ISO 4113 is a category 1 oil.
This category contains low viscosity and mineral oil
that can be reconditioned. Waste oil category 1 must
not contain any foreign substances, e.g. waste oils
belonging to another category, or gasoline.
Disposal of the test oil should be carried out by a
commercial oil disposal specialist in return for a fee.
The associated waste code number 54112 must be
specified in order to guarantee proper disposal.
7.3
Disposal
This EPS 200 is subject to European guide-
lines 2002/96/EG (WEEE).
Old electrical and electronic devices, includ-
ingcables and accessories or batteries must
be
disposed of separate to household waste.
¶
Please use the return and collection sys-
tems in place for disposal in your area.
¶
Damage to the environment and hazards
to personal health are prevented by prop-
erly disposing of EPS 200.
8. Technical data
8.1
EPS 200
!
The grounded, symmetrical 400 Volt and 200 Volt
three-phase power supply must be protected by an FI
protective switch with a rated fault current of 30 mA.
EPS 200 for 230 V
Specification
Rated three-phase voltage
200 VAC − 240 VAC
Rated current
27 A
Fuse
32 A
EPS 200 for 400 V
Specification
Rated three-phase voltage
380 VAC − 460 VAC
Rated current
15 A
Fuse
16 A
Function
Specification
Number of phases
3P / PE
Input frequency
50 Hz / 60 Hz
Nominal power
4.2 KW
Compressed air
0.5 MPa − 0.8 MPa
Storage temperature
-25 °C – 60 °C
*)
Operating temperature
0 °C – 40 °C
*)
Ambient temperature for
measurement accuracy
10 °C – 35 °C
Maximum permissible
relative humidity
≤90 % (at 25 °C and
over 24 hours)
Protection class
IP 34
Oil pressure
180 MPa
Maximum speed
3500 rpm
Control voltage
24 VDC
Rated fault current (residual
current-operated circuit breaker)
30 mA
*)
Longer conditioning times must be expected at ambient tem-
peratures in excess of 77 °F (25 °C).
Function
Specification
Tightening torques for high pressure
connection, sealing screw and hose lines
25 Nm − 30 Nm
Test oil tank capacity
7 l
8.2
Noise emissions
Function
Specification
Workplace noise pressure
level emissions to DIN EN ISO 11201
< 71.5 dB(A)
Sound power level to DIN EN ISO 3744
< 84.1 dB(A)
8.3
Dimensions and weights
Function
Specification
EPS 200 (H x W x D)
580 x 560 x 780 mm
EPS 200 weight with packaging
EPS 200 weight (without test oil and
packaging)
156 kg
112 kg
Oil collecting trough (H x W x D)
30 x 570 x 720 mm
