Belarus 80.1 Series Operation Manual Download Page 268 | Manualshive

Page: 268 / 381

background image

80-0000010B OM

268

Further according to the calculated loads as per table 4.2.2 of load norms, tyre

pressure shall be selected (subsection 4.2.8 “Selecting of optimal inner pressure in tyres
depending on operational conditions and load on tractor axles, instructions for use of
tyres”).

Calculation of tractor controllability criterion without water solution in front tyres:

Calculation of tractor controllability criterion with water solution in front tyres:

, where:

Т

f

is load on front tractor axle, N;

k

f

is tractor controllability criterion;

M

is tractor operational weight (when calculating, the weight of ballasts loads is not

taken into account in tractor operating weight

М

), kg;

m

3

is water solution weight in front tyres of tractor wheels, kg.

g is a value, equal to 9.81 m/s

2

.

ATTENTION: COUPLING OF THE IMPLEMENTS TO THE TRACTOR SHALL NOT

RESULT IN EXCESS OF PERMISSIBLE AXLE LOAD AND LOADS ON THE TRACTOR
TYRES!

ATTENTION: MINIMUM WEIGHT OF THE IMPLEMENTS COUPLED AND BAL-

LAST WEIGHTS USED SHALL ALWAYS MAKE NOT LESS THAN THE VALUES AT
WHICH LOAD ON THE FRONT TRACTOR AXLE IN THE STRUCTURE OF MTU AL-
WAYS MAKES NOT LESS THAN 20% OF THE TRACTOR OPERATING WEIGHT, AND
THE CONTROLLABILITY CRITERION MAKES NOT LESS THAN 0.2!

«
...
266
267
268
269
270
...
»

Summary of Contents for 80.1 Series






























































































































































































































































































































































































Reviews:

No comments

Related manuals for 80.1 Series

Brand: Challenger Pages: 61

Craftsman 944.601901

Brand: Sears Pages: 60

Brand: Expondo Pages: 9

hillvert HT-RUNDLE-5

Brand: Expondo Pages: 11

Brand: New Holland Pages: 2

WILDKAT JD6105-20E T4F

Brand: Tiger Pages: 238

MH 20-4 T BUGGIE

Brand: Manitou Pages: 124

Brand: KitchenAid Pages: 6

Brand: KitchenAid Pages: 12

Brand: KitchenAid Pages: 1

Brand: KitchenAid Pages: 12

Brand: M-B Pages: 427

Brand: Poulan Pro Pages: 60

Brand: NPK Pages: 29

Mikasa MVH-702DRSC

Brand: MULTIQUIP Pages: 58

Brand: MULTIQUIP Pages: 96

Brand: Iran Tractor Pages: 106

Brand: Iran Tractor Pages: 118

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands