Belarus 80.1 Series Operation Manual Download

Page: 156 / 381

80-0000010B OM

156

- 13.6-20 (13.6R20 or 360/70R20) – front tyres, in complete set with rear tyres

16.9R30;

Note – Tyres 11.2R24 and 11.2R42 (9.5-42) are mounted for tractor operation in

spaces between rows of beetroot 450 mm on the track 1800.

When using tyres 15.5R38 and 11.2R42 with loads, exceeding their load capacity,

wheel twinning should be used.

Tyres 9.5-42 shall be used only in twin version.
Contact your dealer for additional advice on twin tyres application.

Parameters of tyres used on tractors “BELARUS-80.1/82.1/820”, are given in table

3.11.1.

Table 3.11.1 – Parameters of tyres

Dimension type

Tyre section, mm

Tyre rolling radius, mm

7.5-20

205

—

11.2-20

284

—

360/70R24

357

—

360/70R20

357

—

9.00R20

234

—

13.6-20(13.6R20)

345

—

11.2R24

284

—

15.5R38

394

750

18.4R34(F-11)

467

770

18.4R30

467

734

16.9R38

429

800

16.9R30

429

698

9.5-42

241

730

11.2R42

284

749

18.4/78-30

(18.4L-30)

470

720

_________________________________________________________________________________

In this section only rear tyre rolling radii are given, which are necessary for

tachospeedometer speed programming as it is specified in subsection 3.18.3 and
3.18.4 “Programming order of tachospeedometer of dashboard with molded panel”.

The rules of tyres operation, selection of optimal tyre inner pressure depending on

the operating conditions and loads on tractor axles, as well as methods of track setting are
given in subsection 4.2. “Tractor use”

Summary of Contents for 80.1 Series






























































































































































































































































































































































































Search results

Summary of Contents for 80.1 Series

Reviews:

Related manuals for 80.1 Series

Brands by name

Popular brands

Belarus 80.1 Series, Operation Manual

Search results

Summary of Contents for 80.1 Series

Reviews:

Related manuals for 80.1 Series

Brands by name

Popular brands