Belarus 80.1 Series Operation Manual Download Page 357

Page: 357 / 381

80-0000010B OM

357

End of Table 7.7.1

Failure,

external manifestation, cause

Troubleshooting

Pressure regulator engages compressor for idle stroke when pressure is below 0.77...0.80

MPa, and for operating stroke when pressure is below 0.65 MPa or over 0.70 MPa

Dirt accumulation in cavities and

channels of pressure regulator

Rinse and clean the pressure regulator

Faulty location of the pressure regula-

tor adjusting cap

Adjust pressure regulator as indicated in section 3.8.3

“Check and adjustment of pneumatic system pressure

regulator”

Damage of rubber parts of pressure

regulator, spring shrinkage

Replace damaged parts or send the pressure regulator

to a repair workshop

Tilting, sticking of spool of the pressure

regulator adjusting part

Ensure free movement of spool, lubricate it or send

pressure regulator to a repair workshop

Pressure regulator goes off frequently (engages the pneumatic compressor)

without air bleeding from the receiver tank

Air leakage from the pneumatic system

or from the pressure regulator, failure of

the pressure regulator backflow valve

Detect and stop air leakages

Pressure regulator operates in the mode of safety valve

Pressure regulator adjusting cap is

turned in to a big value

Adjust pressure regulator as indicated in section

3.8.3 “Check and adjustment of pneumatic system

pressure regulator”

Jamming of pressure regulator

dummy piston

Disassemble pressure regulator and eliminate jam-

ming

Outlet ports in the pressure regula-

tor adjusting cap are clogged

Unclog outlet ports

There is no air feeding into the connecting hose through air bleeding valve of

pressure regulator

Insufficient sinking of air bleeding

valve rod in the pressure regulator

Screw in entirely the nut of the connecting hose on

the fitting

Pressure regulator has switched the

pneumatic compressor to idle stroke

Decrease pressure in the receiver tank to the value

below 0.65 MPa

Ineffective braking of trailed agricultural implement

Faulty adjustment of brake valve

drive

Adjust the brake valve drive as specified in section

3.8.2.2 “Check and adjustment of pneumatic system

brake valve drive”

Brake valve failure

Replace brake valve

Failure in the brake system of the
trailed agricultural implement

Eliminate the failure in the brake system of the trailed
agricultural implement

Brakes of trailed agricultural implement release slowly

Brake valve drive got misadjusted

Adjust the brake valve drive as specified in section

3.8.2.2 “Check and adjustment of pneumatic system

brake valve drive”

Brake valve failure

Replace brake valve

Failure in the trailer brake system

Eliminate the failure in the brake system of the trailed
agricultural implement

ATTENTION: WHILE TROUBLESHOOTING IN THE PNEUMATIC SYSTEM, ALL SELF-

MAINTAINED OPERATIONS RELATED TO PRESSURE REGULATOR ADJUSTMENT AND RE-

PAIR, ARE ALLOWED ONLY AFTER THE END OF TRACTOR WARRANTY PERIOD. OTHER-

WISE THE WARRANTY FOR THE PRESSURE REGULATOR SHALL BECOME VOID. TO RE-

PAIR OR ADJUST YOUR PRESSURE REGULATOR (INCLUDING DURING TM3) DURING

TRACTOR WARRANTY PERIOD CONTACT YOUR DEALER!

Summary of Contents for 80.1 Series






























































































































































































































































































































































































Search results

Summary of Contents for 80.1 Series

Reviews:

Related manuals for 80.1 Series

Brands by name

Popular brands

Belarus 80.1 Series, Operation Manual

Search results

Summary of Contents for 80.1 Series

Reviews:

Related manuals for 80.1 Series

Brands by name

Popular brands