manualshive.com logo in svg

Belarus 80.1 Series, Operation Manual

Introducing the incredibly versatile Belarus 80.1 Series – your go-to agricultural workhorse! For a thorough understanding of its performance and functionality, look no further than our comprehensive Operation Manual. Download your free manual today from manualshive.com and unlock the full potential of your Belarus 80.1 Series equipment.

Share
Download
background image

80-0000010B OM 

 

362

End of Table 7.9.1

 

 

Failure, 

external manifestation, cause 

Troubleshooting 

Increased play in the steering wheel

Cone-shaped pins of HSC hydrau-
lic cylinders or steering link are not 
tightened 

Tighten  pin  nuts  with  the  torque  of  180  to  200  Nꞏm  and 

fasten with split pins 

There  is  clearance  in  steering  link 
joints 

Eliminate the clearance in steering joints, as indicated in sec-

tion 6 “Technical maintenance” 

Worn-out  steering  column  end  ex-
tension splines   

Replace the lower cardan-joint yoke 

Worn-out  steering  column  cardan 
shaft 

Replace cardan shaft 

Spool  recentering  springs  of  dos-
ing pump have lost spring power 

Contact  the  dealer.  Replacement  of  springs,  assembly

and  check  of  operability  shall  be  performed  only  by 

maintenance  department  in  accordance  with  manufactur-

er’s instruction 

1)

 

Incomplete steering angle of steering wheels

Insufficient  pressure  in  the  HSC 

hydraulic system due to the follow-

ing reasons: 

- faulty adjustment of dosing pump 

safety valve (low pressure) 

-   faulty feed pump 

 

 

 

Contact  the  dealer.  It  is  required  to  adjust  the  pressure 

relief valve for the required pressure 

1)

 

Contact the dealer 

Increased FDA gear groups’ steer-

ing torque 

Repair the FDA 

 

Different minimum radius of tractor turning to the left and to the right 

Faulty  toe-in  adjustment  of  front 

wheels 

Adjust toe-in of front wheels as specified in section 6 «Tech-

nical maintenance”

 

Breakdown of feed pump

 

High pressure in the HSC hydraulic 
system due to the following rea-
sons: 
- improper connection of high pres-
sure hoses 
-

 

sticking  of  the  dosing  pump  safety 

valve (possibly due to dirt accumula-
tion) 

 
 
 
Perform the connection in strict observance of the operation 
manual 
Contact the dealer. Rinsing of dosing-pump components is 
required. Assembly and adjustment of safety valve for the 
required pressure and check of operability shall be per-
formed only by maintenance department in accordance with 
manufacturer’s instruction 

1)

 

1)

 Considering extreme complexity and responsibility of the dosing pump from the point of view 

of steering system safety, its assembly and disassembly shall be carried out only by servicing 

personnel of manufacturing company (or other authorized maintenance department), properly 

trained,  having  studied  dosing  pump  design  and  service  and  dosing  pump  assembly-

disassembly manuals, and provided they have all the required service tools, accessories and a 

special hydraulic stand, ensuring adjustment and check of dosing pump parameters and oper-

ability after the repairs have been made. Otherwise, the person performing the dosing pump 

assembly and disassembly, replacement of parts and components or adjustment of valves, as 

well as the tractor owner, bear full responsibility for dosing pump non-operability. 

Summary of Contents for 80.1 Series






























































































































































































































































































































































































Reviews:

No comments

Related manuals for 80.1 Series

Colombia PS15B97 Instruction Manual preview
PS15B97
Brand: Colombia Pages: 72
GOLDONI 85 Operation And Maintenance preview
85
Brand: GOLDONI Pages: 46
Degelman 6900 Series Operator'S Manual/Parts Catalog preview
6900 Series
Brand: Degelman Pages: 33
Bauer Tractor TURBOMIX MTXH Operating Instructions Manual preview
Tractor TURBOMIX MTXH
Brand: Bauer Pages: 42
Cub Cadet 3225 Operator'S Manual preview
3225
Brand: Cub Cadet Pages: 36
Zetor PROXIMA HS Series Operator'S Manual preview
PROXIMA HS Series
Brand: Zetor Pages: 212
Yard-Man 14995-0 Owner'S Manual preview
14995-0
Brand: Yard-Man Pages: 44
ICS LT 120 Assembly Manual And Use And Care preview
LT 120
Brand: ICS Pages: 18
J&M 1520 Operator'S Manual preview
1520
Brand: J&M Pages: 47
wsm m9540 Workshop Manual preview
m9540
Brand: wsm Pages: 73
wsm L3400 Workshop Manual preview
L3400
Brand: wsm Pages: 385
Trejon OPTIMAL M-1650 Mounting Instruction preview
OPTIMAL M-1650
Brand: Trejon Pages: 24
Struck MD750 Operator'S Manual preview
MD750
Brand: Struck Pages: 24
Struck Magnatrac RS1000 Attachment Assembly Instructions preview
Magnatrac RS1000
Brand: Struck Pages: 117
International Harvester Company McCormick Farmall Super C Operator'S Manual preview
McCormick Farmall Super C
Brand: International Harvester Company Pages: 101

Brands by name

Popular brands

Load more brands