Belarus 80.1 Series Operation Manual Download Page 292

Page: 292 / 381

80-0000010B OM

292

- remove cover 1 of oil filler neck of HPS body;

- take out mesh filler filter with oil dipstick 2 and determine the oil level;

- the oil level shall be between the upper (MAX) and lower (MIN) marks of the oil

dipstick;

- place back the mesh filter;

- if necessary, add oil up to the necessary level;

- place back cover 1 of oil filler neck of HPS body.

1 – cover of oil filler neck; 2 – mesh filler filter with oil dipstick; 3 –

cover of HPS

body.

Figure 6.4.8 – Check of oil level in HPS body

ATTENTION: DO NOT LET THE OIL LEVEL DROP BELOW THE LOWER MARK

(MIN) OF OIL DIPSTICK!

6.4.2.6 Operation 15. Check of oil level in bodies of FDA upper bevel pairs with

bevel wheel gear groups

Note – The operation shall be performed on BELARUS-82.1 tractor (FDA with bevel

wheel gear groups).

To check oil level in both bodies of upper bevel pairs 2 (Figure 6.4.9), do the follow-

ing:

- put the tractor on a flat horizontal ground, stop the engine, and brake using the

parking brake;

- turn off plugs of level/fill openings 1 of upper bevel pairs’ 2 bodies;

- make sure that the oil level coincides with the lower edge of level/fill opening;

- if necessary, refill oil into the

upper bevel pairs’ 2 bodies;

- put back the plugs of the level/fill openings;

1 – level/fill opening; 2 – upper bevel pair body.

Figure 6.4.9 – Check of oil level in bodies of FDA upper bevel pairs with bevel

wheel gear groups

Summary of Contents for 80.1 Series






























































































































































































































































































































































































Search results

Summary of Contents for 80.1 Series

Reviews:

Related manuals for 80.1 Series

Brands by name

Popular brands

Belarus 80.1 Series, Operation Manual

Search results

Summary of Contents for 80.1 Series

Reviews:

Related manuals for 80.1 Series

Brands by name

Popular brands