Belarus 80.1 Series Operation Manual Download

Page: 159 / 381

80-0000010B OM

159

Oil tank is combined oil tank 3 of hydraulic lift linkage (HLL) and hydraulic system of

HSC. Oil filtering is carried out through drain filter 5 (rated filter fineness 25 mcm) installed

in the HLL hydraulic system.

In drain hydraulic line “T” lock valve 2 is installed, intended for control of tractor rear

axle differential lock hydraulic coupling.

The connection between the steering wheel and the steering wheels is carried out

hydraulically by means of oil pipelines and high-pressure hoses connecting dosing pump

4, mounted on steering column, and differential hydraulic cylinder 11, mounted on the FDA

body or front axle.

When you turn the steering wheel to the left or right in dosing pump 4 compression

of the centering plate springs and displacement of the distribution grooves of the spool (the

spool is connected to the shaft of the steering wheel through the splines) relative to the

grooves of the sleeve occurs, as a result, oil from feed pump 7 enters under pressure the

corresponding cavity "R" or "L" of steering cylinder 11 through the dosing gerotor unit of

the dosing pump in the volume proportional to the rotation of the steering wheel, and oil

from the other cavity of hydraulic cylinder 11 enters the drain line "T" through the channels

in the spool and the sleeve and is drained into the oil tank.

When you stop turning the steering wheel the sleeve under action of the centering

plate springs of the dosing pump returns to neutral position relative to the spool, cylinder

hydraulic lines “L” and “R” are locked and oil from pressure hydraulic line “P” enters

through the channels in the spool and sleeve on drain “T”, that provides pressure relief in

pressure hydraulic line “P” and relief of feed pump 7.

The locked volume of oil in the cavities of hydraulic cylinder 11 provides stability of

the direction of tractor travel when the steering wheels run-over the unevenness of

the road or soil.

Under normal operating conditions, when feed pump 7 provides the oil pressure re-

quired to turn the guiding wheels, the maximum force applied by the operator to turn the

steering wheel does not exceed 30 N.

If the oil flow from the feed pump is too low or absent (e.g. in case of the diesel en-

gine, feed pump malfunctions, pressure oil pipeline breakage or lack of oil in the tank),

dosing pump 4 acts as a manual pump when the steering wheel is rotated, pumping oil

from one cavity of hydraulic cylinder 11 to the other to ensure that the guiding wheels turn.

The steering force applied by the operator to create the required oil pressure in hydraulic

cylinder 11 during manual operation increases significantly, in some cases up to 600 N.

Table 3.12.1 – Technical characteristics of HSC

HSC parameter designation

Parameter value

BELARUS-80.1/82.1

BELARUS-820

Force on steering wheel, N, not more

Steering wheel play, degrees, not more

Speed of steering wheel “slip” in extreme posi-
tions when force of 100 N is applied

3 r/min, not more

Feed pump:

-type

gear-type

-direction of rotation

Left

-operating volume, cm

Dosing-pump:

-type

gerotor, with open center, without reaction

-operating volume, cm

100

160

-safety valve adjustment pressure, MPa

-anti-shock valves adjustment pressure, MPa

Steering mechanism:

Hydraulic cylinder and steering linkage

-piston diameter, mm

-rod diameter, mm

-rod stroke, mm

200

Summary of Contents for 80.1 Series






























































































































































































































































































































































































Search results

Summary of Contents for 80.1 Series

Reviews:

Related manuals for 80.1 Series

Brands by name

Popular brands

Belarus 80.1 Series, Operation Manual

Search results

Summary of Contents for 80.1 Series

Reviews:

Related manuals for 80.1 Series

Brands by name

Popular brands