Belarus 80.1 Series Operation Manual Download | Manualshive

Page: 185 / 381

background image

80-0000010B OM

185

Partial locking of the internal buckles in working position is carried out according to the

same algorithm as the full locking of the buckles in working position. By rotating buckles 7 in
one or other direction set the required length of the buckles. After the length of the buckles is
set it is necessary to check, whether the required value of the implement swinging in each di-
rection is ensured. If it does not, adjust the length of the buckles once again.

1 – bracket; 2 – bolt; 3 – eyebar; 4 – bolt; 5 – nut; 6 – cotter pin; 7 – buckle;

8 – locknut.

Figure 3.16.6 – Buckle

ATTENTION: WHEN CHANGING THE LENGTH OF THE BRACE IT IS NECES-

SARY TO READJUST THE LOCKING OF THE BUCKLES IN TRANSPORT POSITION.
NONFULFILLMENT OF THIS REQUIREMENT CAN LEAD TO BREAKAGE OF THE LIM-
ITING BUCKLES OR OTHER BREAKAGES!

3.16.2.2 Lifting rod

Two types of lifting rods can be mounted on the tractor: screw-type and gear-type. Upon

request one of the three complete sets of lifting rod pairs can be mounted:

- two gear-type lifting rods;
- one gear-type lifting rod (on the right side along the tractor travel) and one screw-type lift-

ing rod;

- two screw-type lifting rods.

Screw-type lifting rod is shown in figure 3.16.7.

1 – screw with hinge; 2 – buckle; 3 – buckle; 4 – fork.

Figure 3.16.7 – Screw-type lifting rod

Adjust screw-type lifting rod length in the following sequence:
- unscrew locknut 3;
- rotating buckle 2 clockwise or anticlockwise change the length of the lifting rod;
- having adjusted the length of the lifting rod, lock threaded connection by locknut 3.

Gear-type lifting rod is shown in figure 3.16.8.
Adjustment of the lifting rod length is carried out by rotation of handle 5 clockwise or

anticlockwise.

«
...
183
184
185
186
187
...
»

Summary of Contents for 80.1 Series






























































































































































































































































































































































































Reviews:

No comments

Related manuals for 80.1 Series

MAGNATRAC MH8000

Brand: Struck Pages: 69

Brand: Vari Pages: 44

Brand: Howard Pages: 53

Brand: CAMSO Pages: 24

Brand: R2 RINALDI Pages: 32

Brand: Valtra Pages: 51

Brand: jcb Pages: 21

Brand: Pasquali Pages: 65

FENDT 800 Vario SCR Series

Brand: AGCO Pages: 51

MATERIAL'S GRAPPLE

Brand: Koyker Pages: 21

Brand: Koyker Pages: 23

Brand: Koyker Pages: 30

Brand: Koyker Pages: 42

Brand: Claas Pages: 31

AXION 810 CMATIC

Brand: Claas Pages: 41

Brand: Claas Pages: 178

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands