Belarus 80.1 Series Operation Manual Download Page 182

Page: 182 / 381

80-0000010B OM

182

When working with some implements it is necessary to ensure implement swinging

in each side not less than 125 mm or other value in accordance with the operation manual

of the machine (implement). For that, it is necessary to carry out partial locking of the

buckles in working position.

It is necessary to carry out partial locking of the buckles in the working position in

the following way:

- rotating screw 2 (figure 3.16.4), install handle 3 in the middle of flattened surface

“A”;

- remove cotter key 5 from the buckle;

- attach machine (implement) to lower links 7 and slightly lift it until it is off the

ground;

- position the machine (implement) symmetrical to the longitudinal axis of the trac-

tor;

- turn inner tube 4 by hand so that the holes in it are at the top of the tube;

- align one of the holes of inner tube 4 with the nearest hole of outer tube 6 and in-

stall cotter key 5 in them;

- check the value of lateral swinging of the machine (implement), which shall not be

higher than 20 mm in each direction;

- if necessary, adjust value of lateral swinging of the machine (implement) by rotat-

ing screw 2.

а) Partial locking of the telescopic buckles b) Full locking of the telescopic buckles

1 – bracket; 2 – screw; 3 – handle; 4 – inner tube; 5 – cotter key; 6 – outer tube;

7 – lower link.

Figure 3.16.4 – Partial and full locking of the telescopic buckles

Summary of Contents for 80.1 Series






























































































































































































































































































































































































Search results

Summary of Contents for 80.1 Series

Reviews:

Related manuals for 80.1 Series

Brands by name

Popular brands

Belarus 80.1 Series, Operation Manual

Search results

Summary of Contents for 80.1 Series

Reviews:

Related manuals for 80.1 Series

Brands by name

Popular brands