manualshive.com logo in svg

Belarus 80.1 Series, Operation Manual, Page: 334 / 381

Share
Download
Belarus 80.1 Series Operation Manual Download Page 334

80-0000010B OM 

 

334

14.  Check  and,  if  necessary,  tighten  four  nuts  М16  (two  nuts  on  each  side)  of 

wedges of FDA body 72-2300020, with the torque of 110 to 140 N

m. 

 

Note – The operation shall be performed on BELARUS-82.1 tractors. 

 

15. Check and, if necessary, tighten four bolts М12 (two bolts on each side) of flanges 

of pivoted pipes of FDA 72-2300020, with the torque of 60 to 75 N

m. 

 

Note – The operation shall be performed on BELARUS -82.1 tractors. 

 

16. Check and, if necessary, tighten three bolts М16 that attach the body of inter-

mediate support of the cardan drive to the clutch body, with the torque of 100 to 120 N

m. 

 

Note – The operation shall be performed on BELARUS -82.1/820 tractors. 

 

17. Check and, if necessary, tighten the nuts of cone-shaped connection of the pins 

of steering hydraulic cylinder, by doing the following: 

- remove split pins from castellated nuts; 
- Check and, if necessary, tighten, with the torque of 180 to 200 N

m, the castellated 

nuts of pins of steering hydraulic cylinder (two nuts М24 for BELARUS-80.1/82.1, two nuts 
М27 for BELARUS-820); 

- then tighten up the nut so that the nut’s closest groove coincides with the opening 

in the pin, and fasten with a split pin. 

 

Note  –  The  operation  shall  be  performed  for  tractors  equipped  with  HSC  or  HSC 

with HPS body. 

 

18.  Check  and,  if  necessary,  tighten  the  connections  of  HSC  hydraulic  cylinder 

bracket  to  FDA  body  or  front  axle  (four  bolts  М16  with  the  torque  of  180  to  200  N

m

 

for 

BELARUS–80.1;  two  bolts  М16  with  the  torque  of  180  to  200  N

m

 

for  BELARUS–82.1; 

three nuts М16 with the torque of 110 to 140 N

m for BELARUS–820). 

 

Note  –  The  operation  shall  be  performed  for  tractors  equipped  with  HSC  or  HSC 

with HPS body. 

 

19. Check and, if necessary, tighten both nuts М27х1.5 that attach swivel levers to 

front axle knuckles with the torque of 250 to 300 N

m.  

 

Note – The operation shall be performed for BELARUS-80.1 tractors. 

 

20. Check and, if necessary, tighten two locknuts М24х1.5 (with left and right-hand 

threading) of steering link tube, with the torque of 100 to 140 Nꞏm. 

 

Note  –  If  your  tractor  is  equipped  with  HSC  or  HSC  with  HPS  body,  two  steering 

links are mounted.  

 

21.  Check  and,  if  necessary,  tighten  two  castellated  nuts  М18х1.5  of  ball  pins  of 

steering link by doing the following: 

- remove split pins from castellated nuts; 
- tighten each castellated nut with the torque of 100 to 140 N

m; 

- then tighten up each castellated nut until the nearest slot of the nut coincides with 

the hole in ball pin, and fasten with a split pin; 

 

Note – If your tractor is equipped with HSC or HSC with HPS body, two steering 

links are mounted.

 

Summary of Contents for 80.1 Series






























































































































































































































































































































































































Reviews:

No comments