Belarus 80.1 Series Operation Manual Download

Page: 157 / 381

80-0000010B OM

157

3.12 Hydrostatic steering control

3.12.1 General information

Hydrostatic steering control (HSC) is designed to control turning of guiding wheels

and to decrease steering wheel turning force.

1 – oil pipeline of the differential lock coupling; 2 – lock valve; 3 – HLL and HSC

combined oil tank; 4 – dosing pump; 5 – drain filter; 6 – emergency oil pressure sensor;

7 – HSC feed pump; 8 – suction hydraulic line; 9 – swivel lever; 10 – cone pins;

11 – steering hydraulic cylinder; 12 – grease fitting; 13 – cylinder bracket; Р – pressure

hydraulic line; Т – drain hydraulic line; L – left turn hydraulic line; R – right turn hydraulic

line.

Figure 3.12.1 Hydrostatic steering control and differential lock valve (for tractors

BELARUS-820).

Summary of Contents for 80.1 Series






























































































































































































































































































































































































Search results

Summary of Contents for 80.1 Series

Reviews:

Related manuals for 80.1 Series

Brands by name

Popular brands

Belarus 80.1 Series, Operation Manual

Search results

Summary of Contents for 80.1 Series

Reviews:

Related manuals for 80.1 Series

Brands by name

Popular brands