Belarus 80.1 Series Operation Manual Download Page 366

Page: 366 / 381

80-0000010B OM

366

7.12 Possible failures of hydraulic lift linkage and instructions for trouble-

shooting

A list of possible failures of the hydraulic lift linkage and instructions for their trou-

bleshooting are given in Table 7.12.

Table 7.12

Failure,

external manifestation, cause

Troubleshooting

RLL with agricultural implement attached will not rise

No pressure in the hydraulics:



sticking of bypass valve;

Remove the valve parts, rinse and install into the
body. The valve must move freely



clogging of safety valve;

Disassemble the safety valve, rinse, reinstall. Adjust the
valve actuation pressure.



insufficient amount of oil in the

tank.

Add oil to the tank to the recommended level

Loss of pump efficiency

Check pump performance, replace if necessary.

Regulator control rod length is
maladjusted

Adjust

Weight of the implement exceeds
the allowable value for the tractor
lift linkage

Use agricultural implements, as agreed with the manu-
facturer

No forced lift linkage lowering

Regulator control rod is improper-
ly adjusted

Adjust

Slow rise of lifting linkage with agricultural implement attached

Air suction into the hydraulic sys-
tem

Identify place of suction and eliminate the failure

Loss of pump performance

Check pump performance, replace if necessary.

Weight of the implement exceeds
the allowable value for the tractor
lift linkage

Use agricultural implements, as agreed with the manu-
facturer

Oil foaming in oil tank and spitting through the breather

Air suction into the hydraulic sys-
tem through the suction line

Tighten the connection and replace the gaskets of
suction pipe branch if necessary

Air suction through self-tightening
cuffs of the HLL oil pump

Check condition of self-tightening cuffs and replace if
necessary.

Oil level in the tank is too high

Drain excess oil to recommended level.

Increased oil heating during system operation

Insufficient oil in the tank

Add oil to the tank to the recommended level.

Oil lines bent or crumpled

Repair the crumples or replace oil line

Sticking of spool of hydraulic dis-
tributor

Return the levers of hydraulic distributor to the neutral
position after finishing the operation

Hydraulic motors of the imple-
ment are not in agreement with
the tractor pump feed in terms of
consumption

Apply implements as agreed with the manufacturer

Summary of Contents for 80.1 Series






























































































































































































































































































































































































Search results

Summary of Contents for 80.1 Series

Reviews:

Belarus 80.1 Series, Operation Manual, Page: 366 / 381

Search results

Summary of Contents for 80.1 Series

Reviews: