Belarus 80.1 Series Operation Manual Download Page 256

Page: 256 / 381

80-0000010B OM

256

Table 5.4.1 – Specifications of hydraulic drive of BELARUS-80.1/82.1/820 tractors

Parameter designation

Parameter value (characteristic)

1 Paired hydraulic outputs

Side

Rear

Two pairs

One pair

2 Oil drain pipe for hydraulic motors (free

drain)

One, against order

3 Oil consumption through hydraulic out-

puts, l/min

up to 46

4 Rated minimum diameter of oil pipeline,

mm:

- oil pressure pipeline
- oil drain pipeline
- free drain

16.0
25.0

1.0

Hydraulic lift linkage operating pressure,

MPa

1.0

6 Safety valve activation pressure, MPa

-2

7 Allowable extraction of hydraulic fluid

from the tank, l, not more than

8.0

8 Allowable hydrostatic power take-off

(HSPTO), kW, not more than

9.0

9 Fastening threading of fast clutches, mm:

- of oil pressure and drain lines
- of free drain of the oil line

М20



1,5

М20



1,5

________________________________________________________________________________________________________________________________

At rated engine speed

ATTENTION: INSTALLATION OF ADDITIONAL COMPONENTS AND CHANGE

OF HYDRAULIC LIFT LINKAGE PIPELINES ROUTE IS ALLOWED ONLY UPON
AGREEMENT WITH THE MANUFACTURER OR THE DEALER!

Note – Location of hydraulic lift linkage outputs and scheme of their connection to

an external consuming system is shown in figures 2.16.3 and 2.16.5.

Summary of Contents for 80.1 Series






























































































































































































































































































































































































Search results

Summary of Contents for 80.1 Series

Reviews:

Related manuals for 80.1 Series

Brands by name

Popular brands

Belarus 80.1 Series, Operation Manual

Search results

Summary of Contents for 80.1 Series

Reviews:

Related manuals for 80.1 Series

Brands by name

Popular brands