background image

FAQ 

                   

   

DVR  User  Manual

 

 

 

 

92 

 

 

 

Appendix A    FAQ 

 

Q1.

 

 

Why can’t I find the HDD?

 

a.

 

Please  check  the  power  and  SATA  data  cables  of  the  HDD  to  make  sure  they  are  well 

connected. 
b.

 

For  some  DVRs  with  the  1U  or  small  1U  case,  the  power  of  the  adapter  may  be  not 

enough for operating them. Please use the power adaptor supplied along with the DVR. 
c.

 

Please  make  sure  the  HDDs  are  compatible  with  the  DVR. See  Appendix  C  Compatible 

Device List for details. 
d.

 

The HDD could have gone bad. Change a new one. 

 

Q2.

 

  Why are there no images output in some or all of the camera windows? 

a.

 

Please make sure the resolutions of the cameras are supported by the DVR. 

b.

 

Please  make  sure  the  network  cables  of  the  IP  camera  and  DVR  are  both  connected 

properly and the network parameters are set correctly. 
c.

 

Please make sure the analog camera is connected properly. 

d.

 

Please make sure the network and the switch both work normally. 

 

Q3.

 

  The screen has no output after booting the DVR normally. 

a.

 

Please make sure the screen, HDMI or VGA cables are good and well connected. 

b.

 

Please  make  sure  the  screen  supports  the  resolution  of  1280*1024  or  1920*1080.  The 

DVR cannot self adapt to the screen of which the resolution is lower than 1280*1024, and then 
the screen will remind you that the screen resolution is not supported by the DVR or just have 
no display.  Please  change  a  screen  at  1280*1024 or  1920*1080  resolution before  booting  the 
DVR. 
 

Q4.

 

  Forget the passwords? 

a.

 

The password for 

admin 

can be reset through 

Edit Security Question

 function.   

Click 

Edit  Security  Question

  button  in  the  login  window  and  then  enter  the  corresponding 

answer of the selected question in the popup window, the password for 

admin

 will be reset to 

123456

  by  default.  If  you  forget  the  answer  of  the  question,  this  way  will  be  invalid,  please 

contact your dealer for help. 
b.

 

The passwords of other users can be reset by 

admin

, please refer to 10.1.2 Edit User for 

details. 

 

 

 

Q5.

 

  The DVR cannot add up to the maximum number of IP cameras? 

Take  the  4  CH  DVR  as  an  example.  Refer  to  the  picture  below.  The  remaining  bandwidth 
should be larger than the bandwidth of the IP camera you want to add, or you would fail to add 
the  IP  camera.  You  should  lower  the  added  cameras

  bitrate  to  release  the  bandwidth.  It  is 

recommended to add cameras by 

Quickly Add

 for batch adding. 

 

Summary of Contents for AVK-TL91E4-1T










































































































Reviews: