AVYCON AVK-TL91E4-1T User Manual Download Page 68

Page: 68 / 105

Alarm Management

DVR User Manual

③

Drag the camera image to set the motion area. You can set more than one motion area.

Click

“

All

”

to set the whole camera image as the motion area. Click

“

Reverse

”

to swap the

motion area and the non-motion area. Click

“

Clear

”

to clear all the motion areas.

④

Click

“

Apply

”

to save the settings. Click

“

Processing Mode

”

to go to the alarm handling

configuration interface of the motion alarm.

9.2.2 Motion Alarm Handling Configuration

①

Click Start



Settings



Alarm



Motion Alarm to go to the following interface.

②

Enable or disable

“

Snap

”

“

Alarm-out

”

“

Preset

”

“

Buzzer

”

“

Pop-up Video

”

and

“

E-mail

”

The alarm handling setting of motion alarm is similar to that of the sensor alarm (see 9.1
Sensor Alarm for details).

③

Click

“

Apply

”

to save the settings. You can click

“

Motion Settings

”

to go to the motion

configuration interface.

9.3 Exception Alarm

9.3.1 IPC Offline Settings

①

Click Start



Settings



Alarm



Exception



IPC Offline Settings to go to the interface as

shown below.

Summary of Contents for AVK-TL91E4-1T










































































































Search results

Summary of Contents for AVK-TL91E4-1T

Reviews:

Related manuals for AVK-TL91E4-1T

Brands by name

Popular brands

AVYCON AVK-TL91E4-1T, User Manual

Search results

Summary of Contents for AVK-TL91E4-1T

Reviews:

Related manuals for AVK-TL91E4-1T

Brands by name

Popular brands