AVYCON AVK-TL91E4-1T User Manual Download Page 70

Page: 70 / 105

Alarm Management

DVR User Manual

9.4 Alarm Event Notification

9.4.1 Alarm-out

①

Click Start



Settings



Alarm



Event Notification to go to the following interface.

②

Set the delay time and the schedule of each alarm-out. You can click

“

Edit Schedules

”

edit the schedules (see 7.3.1 Add Schedule for details).

③

Click

“

Apply

”

to save the settings. You can click

“

Test

”

to test the alarm output.

9.4.2 E-mail

Click Start



Settings



Alarm



Event Notification



E-mail to go to the e-mail configuration

interface. Set the e-mail address of the recipients. See 11.1.5 E-mail Configuration for details.

9.4.3 Display

Click Start



Settings



Alarm



Event Notification



Display to go to the display configuration

interface. Set the duration time of the pop-up video and the pop-up message box. Click

“

Apply

”

to save the settings.

Summary of Contents for AVK-TL91E4-1T










































































































Search results

Summary of Contents for AVK-TL91E4-1T

Reviews:

Related manuals for AVK-TL91E4-1T

Brands by name

Popular brands

AVYCON AVK-TL91E4-1T, User Manual

Search results

Summary of Contents for AVK-TL91E4-1T

Reviews:

Related manuals for AVK-TL91E4-1T

Brands by name

Popular brands