AVYCON AVK-TL91E4-1T User Manual Download Page 15 | Manualshive

Page: 15 / 105

background image

Introduction

DVR User Manual

9



RS485 Connection

There are two types of RS485 interfaces:

（

Type 1

）

（

Type 2

）

Type 1: The P/Z interfaces are used to connect speed dome. K/B interfaces are used to connect
keyboard.
Type  2:  The  RS485  interfaces  are  not  only  used  to  connect  speed  dome  but  also  to  connect
keyboard.
The way to connect speed dome to the DVR:
Type 1: Disconnect pluggable block from the RS485 terminal block and then loosen the fixed
screws from the pluggable block, insert signal cables into Y and Z port separately (Y is TX+; Z
is TX-) and tighten the fixed screws. Next, connect pluggable block back into terminal block.
Finally, connect the video cable of the speed dome to the video input interface of the DVR.
Type 2: Disconnect pluggable block from the RS485 terminal block and then loosen the fixed
screws from the pluggable block, insert signal cables into A and B port separately (A is TX+; B
is TX-) and tighten the fixed screws. Next, connect pluggable block back into terminal block.
Finally, connect the video cable of the speed dome to the video input interface of the DVR.

Note:

The pluggable block of some models may not be connected into the terminal block and you shall obtain it

from the accessories.

«
...
13
14
15
16
17
...
»

Summary of Contents for AVK-TL91E4-1T










































































































Reviews:

No comments

Related manuals for AVK-TL91E4-1T

Brand: Ebode Pages: 104

Brand: W Box Pages: 67

Brand: Mediacom Pages: 8

Brand: CasaCam Pages: 31

Brand: XTS Pages: 17

Brand: Digisol Pages: 70

Brand: Aspiring Pages: 44

Brand: Digital Watchdog Pages: 60

Brand: Ganz Pages: 51

Brand: Zoom Pages: 24

Ki Pro Ultra 12G

Brand: AJA Pages: 98

Brand: Ness Pages: 62

Ultimate Premium H.264

Brand: Ness Pages: 70

Brand: ClearView Pages: 7

Brand: Plantron Pages: 48

DS-7204HUHI-K1/E

Brand: HIKVISION Pages: 4

Brand: HIKVISION Pages: 29

Brand: Veyo Pages: 39

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands