AVYCON AVK-TL91E4-1T User Manual Download Page 49

Page: 49 / 105

Record & Disk Management

DVR User Manual

Record & Disk Management

7.1 Record Configuration

7.1.1 Mode Configuration

Please format the HDDs before recording (refer to 7.5 Disk Management for details). Click
Start



Settings



Record



Mode Settings to go to the mode settings interface. You can set the

record time under the

“

Manual Record Settings

”

and then click

“

Apply

”

button to save the

settings. There are two record modes: auto mode and manual mode.



Auto Mode

Motion Record

: Motion alarm record will be enabled when motion alarm happens.

Sensor Record

Sensor alarm record will be enabled when sensor alarm happens.

Motion Sensor Record

Motion/sensor alarm record will be enabled when

motion/sensor alarm happens.

Always(24

ⅹ

7) Motion Record

Normal record is enabled all the time; motion alarm

record will be started when motion alarm happens.

Always(24

ⅹ

7) Sensor Record

: Normal record is enabled all the time; sensor alarm

record will be started when sensor alarm happens.

Always(24

ⅹ

7) Motion Sensor Record

Normal record is enabled all the time;

motion/sensor alarm record will be enabled when motion/sensor alarm happens.

Select one auto mode to pop up the corresponding window. Set the encode, resolution, FPS,
bitrate type, quality, max bitrate and audio of each camera and then click

“

”

to save the

settings. Please adjust the parameters according to the actual condition.

Summary of Contents for AVK-TL91E4-1T










































































































Search results

Summary of Contents for AVK-TL91E4-1T

Reviews:

Related manuals for AVK-TL91E4-1T

Brands by name

Popular brands

AVYCON AVK-TL91E4-1T, User Manual

Search results

Summary of Contents for AVK-TL91E4-1T

Reviews:

Related manuals for AVK-TL91E4-1T

Brands by name

Popular brands