AUX DC Inverter Free Match 50HZ R410A
Installation
88
◇
Avoid that only four angles metal sheet to support the outdoor unit.
Transport
When the outdoor unit is to be lifted, please use two slings longer than 8m and insert cushioning material between
the slings and outdoor unit to avoid damaging the casing.
8.2 Connection piping installation
Piping installation precaution
Please choose copper pipe as the piping.
◇
If the piping installation needs welding:
Please welding before fasten the nut, when welding using nitrogen gas to replace the air in the pipe in order to
prevent oxidation.
◇
If there are many points to be welded ,please set a filter in the pipe(buy from local market)
◇
Please use nitrogen gas or air to remove the dust and water in the pipe,
◇
Please lay out the piping according to the tend towards of the piping, but it is not allowed more than 3 times curved
at the same point of the pipe(if do like this the pipe will become rigid)
◇
When using pipe bending machine, the curvature shall not be too small or it will affect the refrigerant flow.
Piping specification selection
As to the detail selection please take reference to the cooling capacity adjust index figure during different installation
situations.
Piping diameter
Tighten torque
Expanding size (A)
Expanding shape
Paint the frozen oil
1/4in(φ6.35mm)
15-19(N·m)
8.3-8.7mm
3/8in(φ9.52mm)
35-40(N·m)
12.0-12.4mm
1/2in(φ12.7mm)
50-60(N·m)
15.4-15.8mm
5/8in(φ15.88mm)
62-76(N·m)
18.6-19.0mm
3/4in(φ19.05mm)
70-75(N·m)
22.9-23.3mm
Piping connection
◇
Using expanding machine to expand accessories, the size of horn shown in the above figure:
◇
Paint a thin layer of frozen oil at both inside and outside part of the expanding.
◇
Make the expanding right to the screw thread shape connection of the indoor unit, using hands to tighten the nut
then using a wrench to tighten the nut again.
◇
Take out the cover of the indoor unit gas valve and liquid valve, make the expanding right to the stop valve of
outdoor unit, using hands to tighten the nut then using a wrench to tighten the nut again.
Summary of Contents for AMCA-H09/4R1A
