Amtech Axpert-Eazy AMT-011-4, Instruction Manual

Page: 70 / 242

Amtech
6-24
6
MODE-D: Auxiliary Drive Parameters
No. Parameter Unit Def Min Max Res Description WP
GROUP-1: MOTOR PARAMETERS
D101 Motor Voltage Vac 415 380 480 1 This is the Motor rated Voltage. Set the voltage
mentioned on the motor nameplate. The setting
value depends on the 400V, 500V, 600V or
200V Series model.
575 500 575
690 600 690
230 200 240
D102 Motor Current Amp M304 0.3*
M304
M304 0.1 Insert the rated motor current from the
nameplate.
D103 Motor Frequency Hz 50.0 10.0 600.0 0.1 Set the rated base frequency from the
nameplate.
D104 Motor Speed rpm 1500 1 36000 1 Set the base speed from the motor nameplate.
D105 Motor Output
Rating
kW M305 0.1 1500.0 0.1 The motor’s rated output at the base speed is
set from the nameplate.
GROUP-2: FREQUENCY SETTING
D201 Local Set
Frequency
Hz 10.00 0.00 600.00 0.01 This is the frequency set from the operation
panel for auxiliary motor.
D202 Min Frequency Hz 0.10 0.00 600.00 0.01 These two Parameters are used to configure
Minimum and Maximum Frequency of the AC
DRIVE for auxiliary motor.
D203 Max Frequency Hz 50.00 0.10 600.00 0.01
D204 Frequency
Reference Input
1 1 18 1 This is used to select the speed reference for
auxiliary drive.
=1: Local
=3: FSI 4-20mA
=5: FSI 0-20mA
=7: FSI 20-4mA
=9: FSI 20-0mA
=11: Serial
=13: VIN 0-10V
=15: PLC A-O/P 1
=17: PLC A-O/P 3 =2: FSV 0-10V
=4: FSV 0-5V
=6: FSV 10-0V
=8: FSV 5-0V
=10: Static pot
=12: PID Output
=14: IIN 4-20mA
=16: PLC A-O/P 2
=18: PLC A-O/P 4
D205 Line Speed Setting rpm 1500 0 3000 1 The set value will be displayed as motor speed
in
M102 at 50Hz when auxiliary drive is
selected.
D206 Acceleration Time-
1
Sec 10.0 0.1 6000.0 0.1 Time needed for the speed to change from zero
to maximum.
D207 Deceleration Time-
1
Sec 20.0 0.1 6000.0 0.1 Time needed for the speed to change from
maximum to zero.
GROUP-3: TORQUE BOOST
D301 Manual Torque
Boost
Setting
% 0 0.0 20.0 0.1 When setting manually, set the boost voltage at
0Hz as a percentage in respect to the rated
output voltage. When programmed to zero, it
will be disabled. This is automatically adjusted
by the automatic tuning.
D302 Slip Compensation Hz 0.0 0.0 5.0 0.1 Set the motor’s rated slip. When setting
manually, set the slip frequency for the motor
rated load in respect to the base frequency. The
output frequency changes according to the
motor rated torque.
D303 DC Brake Start
Frequency
Hz 1.50 0.00 50.00 0.01 It is a frequency at which DC braking is initiated
during stop.
D304 DC Brake Current % 50 15 150 1 Configure amount of current available for the
DC braking when DC braking is used during
stop.