Amtech Axpert-Eazy AMT-011-4, Instruction Manual

Page: 64 / 242

Amtech
6-18
6
No. Parameter Unit Def Min Max Res Description WP
C206 Vout-2 Gain 1.000 0.100 2.500 0.001 This is gain setting for the VO2 analog output.
C207 Iout-1 Gain 1.000 0.100 2.500 0.001 This is gain setting for the IO1 analog output.
C208 Iout-1 Bias 1000 100 1500 1 This is bias setting for the IO1 analog output.
C209 Iout-2 Gain 1.000 0.100 2.500 0.001 This is gain setting for the IO2 analog output.
C210 Iout-2 Bias 1000 100 1500 1 This is bias setting for the IO2 analog output.
C211 FSV Gain 1.000 0.100 1.500 0.001 This is gain setting for the FSV analog input.
C212 FSV Bias 100 0 1000 1 This is bias setting for the FSV analog input.
C213 FSI Gain 1.000 0.100 1.500 0.001 This is gain setting for the FSI analog input.
C214 FSI Bias 1000 0 1500 1 This is bias setting for the FSI analog input.
C215 VIN Gain 1.000 0.100 1.500 0.001 This is gain setting for the VIN analog input.
C216 VIN Bias 100 0 1000 1 This is bias setting for the VIN analog input.
C217 IIN Gain 1.000 0.100 1.500 0.001 This is gain setting for the IIN analog input.
C218 IIN Bias 1000 0 1500 1 This is bias setting for the IIN analog input.
C219 FSV/FSI Time
Constant
mS 100 0 1000 1 This parameter set the filter time constant for
the FSV and FSI analog inputs.
C220 VIN/IIN Time
Constant
mS 100 0 1000 1 This parameter set the filter time constant for
the VIN and IIN analog inputs.
C221 Vout-1 Bias 100 0 1000 1 This is bias setting for analog output voltage
VO1.
C222 Vout-2 Bias 100 0 1000 1 This is bias setting for analog output voltage
VO2.
C223 Input voltage gain 1.000 0.100 2.000 0.001 This parameter sets the gain for VRY (M201)
and VYB (M202) monitor.
GROUP-3: STATUS OUTPUT DETECTION LEVEL
C301 Frequency
Attainment
Detection Width
% 1.0 0.0 20.0 0.1 The attained frequency output ( Freq Attain )
operation width is set.
C302 I-Detection Level
(current detection)
% 100.0 5.0 200.0 0.1 The current detection ( I-Detection ) operation
level is set. Set with a percentage of the rated
current (
B103 ). The hysteresis will occur with
set value in parameter C314 for the I-Detection
operation.
C303 Speed Detection
Level-1
% 95.0 1.0 105.0 0.1 The speed detection operation level is set. Set
with a percentage to the max frequency
A103 .
The output frequency or the motor speed will be
the comparison target. A 1% hysteresis will
occur with speed detection operation.
C304 Speed Detection
Level-2
% 50.0 1.0 105.0 0.1
C305 Zero Speed
Detection Level
% 1.0 0.0 50.0 0.1 The Zero speed detection operation level is set.
Set with a percentage to the max frequency
(
A103
). The output frequency or the motor
speed will be the comparison target. A 1%
hysteresis will occur with zero speed operation.
C306 4-20mA Reference
Loss
2 1 7 1 This parameter configures the AC DRIVE’s
response to a failure of 4-20mA Frequency
reference input signal.
=1: No action at fault detection
=2: Minor fault alarm & run at minimum speed
=3: Minor fault alarm & run at maximum speed
=4: Minor fault alarm & run at set speed
=5: Minor fault alarm & run at preset speed-1
=6: Fault, ramp down to stop
=7: Fault, coast to stop