Zeiss LSM 710 Скачать руководство пользователя страница 563 | Manualshive

Страница: 563 / 736

background image

LSM 710 and LSM 780

ANNEX

Systems

Beam path Configuration Guide for …

Carl Zeiss

02/2010 M60-1-0025

e

9

Line and Frame Mode of Multitracking

•

Settings can be used for

Line

or

Frame

wise multi-tracking acquisition.

•

In Line mode the lines are scanned in turns for all tracks with the corresponding laser lines turned on
exclusively. Preferred for living samples with moving objects. Acquisition time can be reduced using
bidirectional scan mode.

•

In Frame mode, the whole frames are scanned in turns for all tracks with the corresponding laser lines
turned on exclusively. This mode can be advantageous for dyes that tend to bleach and need time to
recover.

•

There are parameters that can be changed quickly in a line wise acquisition: Digital Gain, Digital
Offset, Laser Line Attenuation,

•

Any other changes of track settings of the selected tracks, e. g. different filters, dichroics or Detector
Gain settings, need a bit more time to be changed and therefore should be changed only when Frame
mode is used.

•

There is a fast Frame mode, which requires identical settings of these parameters.

7.3.3

Beam path Configuration for Multi Photon Excitation

•

The beam path configuration for multi photon excitation follows the same rules as described for a
single and multi track configuration (see above, paragraph 7.3.2)

•

Use a MBS 690+ or MBS 760+ as main dichroic beam splitter to deflect the IR excitation light
(690 or 760 -1050 nm) onto the specimen.

•

On the detection side, use an additional band pass filter in front of the NDD to prevent a
bleed through of IR excitation light to the detector.

7.3.4

Acquisition conditions for RICS

For RICS the pixel size should be at least 5 times smaller than the PSF of the objective, so appropriate
zooms have to be employed.

For the C-Apo 40 x objective with a beam radial extension of approximately 0.25 um zoom factors of
10-20 will guarantee a sufficient size ratio. In addition, scanning spead should not be too high or slow.

As a rule of thumb for solution studies speeds 7-8, for measurements in cytodol and nucleus of 5-6 and
for membrabe studies of 3-4 will be appropriate.

Expression levels should not be too high. A maximum of 1 uM concentration can be tolerated.

«
...
561
562
563
564
565
...
»

Содержание LSM 710

































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для LSM 710

Бренд: Olympus Страницы: 16

Бренд: Hamilton/Buhl Страницы: 9

Бренд: Tecnai Страницы: 22

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 4

Бренд: Discovery Telecom Страницы: 4

Бренд: Levenhuk Страницы: 5

Бренд: Scorpio Страницы: 32

Бренд: Valley Microscope Страницы: 7

Бренд: Olympus Страницы: 18

Бренд: Olympus Страницы: 44

Бренд: Zeiss Страницы: 2

Бренд: THORLABS Страницы: 24

Бренд: STEINDORFF Страницы: 15

Бренд: MicroLinks Tech Страницы: 8

Бренд: OPTO-EDU Страницы: 31

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды