YASKAWA SI-ES3 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 62

YASKAWA SI-ES3 Скачать руководство пользователя страница 6

6

YASKAWA ELECTRIC

SIEP C730600 64A 1000-Series Option SI-ES3 Technical Manual

2 Product Overview

2

Product Overview

About This Product

This option provides a communications connection between the drive and an EtherCAT network. The option connects the
drive to an EtherCAT network and facilitates the exchange of data.

This manual explains the handling, installation and specifications of this product.

EtherCAT is a communications link to connect industrial devices (such as smart motor controllers, operator interfaces,
and variable frequency drives) as well as control devices (such as programmable controllers and computers) to a
network. EtherCAT is a simple, networking solution that reduces the cost and time to wire and install factory automation
devices, while providing interchangeability of like components from multiple vendors.

By installing the option to a drive, it is possible to do the following from an EtherCAT master device:

• drive operation
• drive operation status monitoring
• changing parameter settings.

The option provides instant connectivity to an EtherCAT network for the Yaskawa A1000 drive. The option supports the
Velocity mode according the CANopen Device Profile and Motion Control (DSP402) profile. It also contains Yaskawa
vendor specific CANopen objects based on the present CANopen option board specification.

The EtherCAT Option supports the following communication profiles:

• DS 301 Ver. 4.02
• DSP 402 Ver. 3.0 Velocity Mode

Figure 1

Figure 1 EtherCAT Conformance Tested

Applicable Models

The option can be used with the drive models in

Table 1

.

Table 1 Applicable Models

Drive Series

Drive Model Number

Software Version

<1>

<1> See “PRG” on the drive nameplate for the software version number.

A1000

CIMR-A

2A

≥

1017

CIMR-A

4A

«
...
4
5
6
7
8
...
»

Содержание SI-ES3































































Отзывы:

Нет отзывов