YASKAWA SI-ES3 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 62

YASKAWA SI-ES3 Скачать руководство пользователя страница 18

6 DSP301 and DSP402 Specifications

18

YASKAWA ELECTRIC

SIEP C730600 64A 1000-Series Option SI-ES3 Technical Manual

Implemented CANopen Objects/Components

Communication and parameters on CANopen are built around objects using the following message types.

• SDO (Service Data Object)

The SDO object uses asynchronous data transmission and is used to access objects without mapping them to an I/O
(PDO) connection. With SDO communication, the user will have access to all CANopen objects in the option.

• Process Data Object (PDO)

The PDO object is used for I/O communication.

• Emergency Object (EMCY)

Emergency object is used for error reporting when a fault has occurred in the drive or option.

Services

Supported SDO Requests

• SDO Download Expedited

Writes up to four octets to the slave

• SDO Download Normal

Writes up to a negotiated number of octets to the slave

• Download SDO segment

Writes additional data if the object size is greater than the negotiated number of octets

• SDO Upload Expedited

Reads up to four octets from the slave

• SDO Upload Normal

Reads up to a negotiated number of octets from the slave

• Upload SDO segment

Reads additional data if the object size is greater than the negotiated number of octets

• Abort SDO Transfer

Server abort of service when error is detected

Emergency Service

• Emergency (Does not support incoming requests)

Report of unexpected conditions

«
...
16
17
18
19
20
...
»

Содержание SI-ES3































































Отзывы:

Нет отзывов