YASKAWA SI-ES3 Скачать руководство пользователя страница 50

Страница: 50 / 62

10 Process Data Objects (PDO)

YASKAWA ELECTRIC

SIEP C730600 64A 1000-Series Option SI-ES3 Technical Manual

Accessed Drive Registers

Table 19

describes the accessed drive registers.

Table 19 Accessed Drive Registers

0x604C#1

0x00000001

32-bits

0x604C#2

0x00000001

32-bits

Reg.

Address

Internal Name/Short

Used in Context Evaluation

Description

Option Access

(RO/RW/WO)

0x003E

INVR_U102_OUTFREQ_RPM CoE: 0x6043 (vl velocity demand)

Output freq
[Unit: 1.0 r/min]

0x00AC

INVR_U105_MSPEED_RPM

CoE: 0x6044 (vl velocity actual value)

Motor speed (U1-05)
[Unit: 1.0 r/min]

0x0041

INVR_U102_OUTFREQ

CoE: 0x2110 (Output frequency)

Output freq (U1-02)
[Unit: o1-03]

0x00FB

INVR_U103_OUTCUR2

CoE: 0x2120 (Output current)

Output current (U1-03)

0x0048

INVR_U109_OUTTRQREF

CoE: 0x2130 (Output torque reference)

Torque reference (U1-09)
[Unit: 0.1%]

0x0049

INVR_U110_TER_DIN

• CoE: 0x2180 (Free output default)
• CoE: 0x2270 (Drive DI input)

Input terminal status (U1-10)

0x0044

INVR_U105_MSPEED

CoE: 0x2200 (Motor speed)

Motor speed (U1-05)
[Unit: o1-03]

0x0046

INVR_U107_DCBUSVOLT

CoE: 0x2210 (DC bus voltage)

Bus voltage
[Unit: 1.0 V]

0x004A

INVR_U111_TER_OUT

CoE: 0x60FD (Digital inputs)

Output terminal status
(U1-11)

0x004E

INVR_U113_TER_A1IN

• CoE: 0x2190 (Free output default)
• CoE: 0x2220 (Analog input monitor A1)

A1 terminal level voltage
(U1-13)

0x004F

INVR_U114_TER_A2IN

CoE: 0x2240 (Analog input monitor A2)

A2 terminal level voltage
(U1-14)

0x0050

INVR_U114_TER_A3IN

CoE: 0x2260 (Analog input monitor A3)

A3 terminal level voltage
(U1-15)

0x0080

INVR_U201_FAULTCUR

EtherCAT CoE Emergency services

Current fault (U2-01)

0x0001

INVR_INVCTRL1

• CoE: 0x6040 (DSP402 controlword)
• CoE: 0x60FE (Digital outputs)
• CoE: 0x2000 (Operation command)

Run operation signal (option)

0x0002

INVR_OPT_FREQ_REF

CoE: 0x2010 (Speed reference/Speed limit)

Frequency reference

0x0004

INVR_OPT_TORQUE_REF

CoE: 0x2020 (Torque reference/Torque limit)

Torque reference/limit
[Unit: 0.1%]

0x0005

INVR_OPT_TORQUE_COMP

CoE: 0x2030 (Torque compensation)

Torque compensation
[Unit: 0.1%]

0x0007

INVR_OPT_FM_AOUT1

CoE: 0x20D0 (Analog output terminal FM
setting)

Analog output terminal FM
setting

0x0008

INVR_OPT_AM_AOUT2

CoE: 0x20E0 (AM analog output)

AM analog output

0x0009

INVR_OPT_MFUNC_DO

CoE: 0x20F0 (Multi-function DO output)

Multi function DO

0x0200

INVR_C101_ACC1

CoE: 0x6048 (vl velocity acceleration)

Acceleration time 1 (C1-01)
[Unit: C1-10]

0x0201

INVR_C102_DEC1

CoE: 0x6049 (vl velocity deceleration)

Deceleration time 1 (C1-02)
[Unit: C1-10]

0x0208

INVR_C109_FASTSTOP

CoE: 0x604A (vl velocity quick stop)

Fast Stop time (C1-09)
[Unit: C1-10]

0x0209

INVR_C110_ADTUNIT

• CoE: 0x6048 (vl velocity acceleration)
• CoE: 0x6049 (vl velocity deceleration)
• CoE: 0x604A (vl velocity quick stop)

Accel/Decel Time Setting
Units (C1-10)

0x0289

INVR_D201_FREQUL

CoE: 0x6046#2 (vl velocity max amount)

Frequency Reference Upper
Limit (d2-01)

0x028A

INVR_D202_FREQLL

CoE: 0x6046#1 (vl velocity min amount)

Frequency Reference Lower
Limit (d2-02)

CANopen Object

Default Value

Consumed EEPROM Size

Содержание SI-ES3































































Результаты поиска

Содержание SI-ES3

Отзывы:

YASKAWA SI-ES3, Техническое руководство, Страница: 50 / 62

Результаты поиска

Содержание SI-ES3

Отзывы: