manualshive.com logo in svg

YASKAWA SI-ES3, Техническое руководство, Страница: 36 / 62

Поделиться
Скачать
YASKAWA SI-ES3 Скачать руководство пользователя страница 36

8  Object Dictionary

36

 

YASKAWA ELECTRIC

 SIEP C730600 64A 1000-Series Option SI-ES3  Technical Manual

„

2120 (Hex) - Output Current

This object can be used to monitor the drive output current in units of Ampere. The current value resolution is the same 
as in drive monitor U1-03 (for details refer to the technical manual of the drive).

„

2130 (Hex) - Output Torque Reference

This object can be used to monitor the output torque reference.

The availability of this object content depends on the drive control mode. If the selected control mode does not support 
this monitor (equal to drive monitor U1-09), the torque reference monitor value will be 0. Refer to the drive technical 
manual for details.

„

2140 (Hex) - MEMOBUS/Modbus Read Response

This object contains the data of the drive MEMOBUS/Modbus register specified in object 2040 (Hex). Bytes 1 and 2 of 
subindex 1 will contain the data, and bytes 3 and 4 will contain the MEMOBUS/Modbus Address read.

Value: 0xAAAABBBB

0xAAAA = Drive register

0xBBBB = Data

„

2150 (Hex) - MEMOBUS/Modbus Write Response

This object contains the response from the drive when writing a drive parameter using a MEMOBUS/Modbus write 
command (object 2050 (Hex)). Bytes 1 and 2 of subindex 1 will contain the data that were written, and bytes 3 and 4 will 
contain the MEMOBUS/Modbus Address that was written to.

Value: 0xAAAABBBB

0xAAAA = Drive register

0xBBBB = Data

„

2155 (Hex) - PDO Parameter Write Response

Note:

Object only available in EtherCAT SAFEOP or Operational state. Object data is always cleared when a transition from PREOP to 
SAFEOP is done.

Index 

(Hex)

Subindex

Content

Default

Access

PDO 

Mapping 

Value Range

2120

–

Output current

–

Read Only

–

–

1

Value

–

Read Only

Tx

Unsigned 16

2

MEMOBUS/Modbus register address

00FB (Hex)

Read Only

No

Unsigned 16

Value (MEMOBUS/Modbus register): 0x00FB (Output current)

Index 

(Hex)

Subindex

Content

Default

Access

PDO 

Mapping 

Value Range

2130

–

Output torque reference

–

Read Only

–

–

1

Value

–

Read Only

Tx

Unsigned 16

2

MEMOBUS/Modbus register address

0048 (Hex)

Read Only

No

Unsigned 16

Value (MEMOBUS/Modbus register): 0x0048 (Output torque reference)

Index (Hex)

Subindex

Content

Access

PDO Mapping 

Value Range

2140

0

Number of entries

Read Only

No

Unsigned 8

Value: 0x01

1

MEMOBUS/Modbus read response

Read Only

Tx

Unsigned 32

Index (Hex)

Subindex

Content

Access

PDO Mapping 

Value Range

2150

0

Number of entries

Read Only

No

Unsigned 8

Value: 0x01

1

MEMOBUS/Modbus write response

Read Only

Tx

Unsigned 32

Содержание SI-ES3































































Отзывы:

Нет отзывов