manualshive.com logo in svg

YASKAWA SI-ES3, Техническое руководство, Страница: 29 / 62

Поделиться
Скачать
YASKAWA SI-ES3 Скачать руководство пользователя страница 29

8  Object Dictionary

YASKAWA ELECTRIC

 SIEP C730600 64A 1000-Series Option SI-ES3  Technical Manual

 29

„

1010 (Hex) - Store Parameters

By writing “save” (s = 73H, a = 61H, v = 76H, e = 65H) to this object, the EtherCAT Option settings are saved in the 
non-volatile memory. The EtherCAT Option will operate using these settings when a Reset Node or Reset 
Communications command is performed or when the power supply is cycled.

Default read value: 0x01 (Save on command)

Behavior: Write of value 0x0000 to MEMOBUS/Modbus register: 0x0900. Issue EEPROM ENTER command to the 
drive.

Note:

Write access is only allowed in the EtherCAT Pre-Operational state.

„

1011 (Hex) - Restore Default Parameters

Writing “load” (l = 6CH, o = 6FH, a = 61H, d = 64H) to subindex 1 restores the EtherCAT Option default settings.

Default read value: 0x01 (Restore on command)

Behavior: Option will write value = 2220 to MEMOBUS/Modbus register: 0x0103 (A1-03) together with an EEPROM 
ENTER command

Note:

Write access is only allowed in the EtherCAT Pre-Operational state.

„

1018 (Hex) - Identity Object

This object contains general information about the drive.

Index (Hex)

Subindex

Content

Access

PDO Mapping 

Value Range

1010

1

 Store parameters 

Read/Write

 No

Unsigned 32

Index (Hex)

Subindex

Content

Access

PDO Mapping 

Value Range

1011

1

Restore default parameters

Read/Write

 No 

Unsigned 32

Index (Hex)

Subindex

Content

Access

PDO Mapping 

Value Range

1018

–

Identity object

Read/Write

–

Unsigned 32

0

Number of entries

Read Only

No

Unsigned 8

Value: 4

1

Vendor ID

Read Only

No

Unsigned 32

Yaskawa ETG Member Vendor ID
Value: 0x00000539 (Yaskawa Electric Corporation, Japan)

2

Product Code

Read Only

No

Unsigned 32

EtherCAT option product code
Value: 0x53455333 (ASCII: SES3)

3

Revision number

Read Only

No

Unsigned 32

Yaskawa EtherCAT option software revision number.
Definition: xxxxxYYYY ' (xxxx = Major, YYYY = Minor)
Value: 9242.xx00
9 = A1000 option card
2 = European product
42 = Product code
xx = Minor revision

4

Serial number

Read Only

No

Unsigned 32

EtherCAT option serial number

Содержание SI-ES3































































Отзывы:

Нет отзывов