YASKAWA SI-ES3 Скачать руководство пользователя страница 55

Страница: 55 / 62

12 Fault Diagnosis and Possible Solutions

YASKAWA ELECTRIC

SIEP C730600 64A 1000-Series Option SI-ES3 Technical Manual

SDO Abort Codes

SDO abort codes are supported as specified in DS301. Additionally the abort codes listed below are implemented.

Table 22 SDO Abort Codes

4310

Motor overheat fault (PTC input)

oH4

0x20

FF08

MEMOBUS/Modbus communication error

0x21

FF07

Option communication error

bUS

0x22

FF06

Control fault

0x25

8313

Zero servo fault

SvE

0x26

5481

Option card external fault

EF0

0x27

FF02

PID feedback loss

FbL

0x28

FF03

Undertorque detection 1

UL3

0x29

FF04

Undertorque detection 2

UL4

0x2A

FF05

High slip braking oL

oL7

0x2B

6000

Hardware or communication error of drive or option

/CPF

0x30

FF32

Z pulse fault (Closed Loop Vector for PM motors)

dv1

0x32

FF33

Z pulse noise fault detection (Closed Loop Vector for PM
motors)

dv2

0x33

FF34

Inversion detection (Closed Loop Vector for PM motors)

dv3

0x34

FF35

Inversion prevention detection (Closed Loop Vector for PM
motors)

dv4

0x35

FF36

Output current imbalance

LF2

0x36

FF37

Pull-out detection

STo

0x37

FF38

PG disconnect (control mode with PG)

PGoH

0x38

FF3B

Too many speed search restarts

SEr

0x3B

FF41

PID feedback loss

FbH

0x41

FF0D

External fault (input terminal S1)

EF1

0x42

FF0E

External fault (input terminal S2)

EF2

0x43

FF44

Mechanical weakening detection 1

oL5

0x44

FF45

Mechanical weakening detection 2

UL5

0x45

FF46

Current offset fault

CoF

0x46

FF47

PLC detection error 1

PE1

0x47

FF49

DriveWorksEZ fault

dWFL

0x49

6301

Error during object content selection

–

SDO Abort Code

Description

0602 0010 (Hex)

Consecutive MEMOBUS/Modbus Read/Write/ENTER commands are send but the wait time between messages
is too short.

A MEMOBUS/Modbus Read or Write Response (2140 (Hex) and 2150 (Hex)) was attempted but no or an
incorrect MEMOBUS/Modbus address has been written to object 2040 (Hex) or 2050 (Hex) before.

A MEMOBUS/Modbus write request has been sent during DC bus under voltage.

0602 0022 (Hex)

Drive Profile DSP402 is used and a value is written to object 6042 (Hex) (vl Target Velocity) while the drive
status is not “Operation Enable”.

Object 2155 (Hex) is tried to be read while the option is not in Operational state.

A MEMOBUS/Modbus Read or Write command (2040 (Hex) and 2050 (Hex)) was performed with an invalid
MEMOBUS/Modbus address.

Error Code (Hex)

Meaning

Drive Display

MEMOBUS/Modbus

Register: 0x0080

Enum Value

Содержание SI-ES3































































Результаты поиска

Содержание SI-ES3

Отзывы:

YASKAWA SI-ES3, Техническое руководство, Страница: 55 / 62

Результаты поиска

Содержание SI-ES3

Отзывы: