manualshive.com logo in svg

YASKAWA SI-ES3, Техническое руководство, Страница: 19 / 62

Поделиться
Скачать
YASKAWA SI-ES3 Скачать руководство пользователя страница 19

6  DSP301 and DSP402 Specifications

YASKAWA ELECTRIC

 SIEP C730600 64A 1000-Series Option SI-ES3  Technical Manual

 19

‹

EtherCAT State Machine

Figure 11  

Figure 12  EtherCAT State Machine

The option enters the INIT state directly after start-up. After this, the option can be switched to the Pre-Operation 
(PREOP) state. In the PREOP state, drive parameters can be accessed by CoE SDO.

After the master has configured the slave, the option can be switched to Safe-Operation (SAFEOP) state. In the SAFEOP 
state, Input I/O data (PDOs) will be sent from the option to the EtherCAT master, but there may be no void Output I/O 
data from the master to the option. 

When the transition from PREOP to SAFEOP occurs, the option will process the configured PDO assignments and 
re-map the relevant drive registers. After this, the option will enter the SAFEOP state.

In order to communicate Output I/O data, the master must switch the option to Operation (OP) state.

„

EtherCAT Operation Mode Relations

Table 5  EtherCAT Operation Mode Relations

Note:

If the requested drive state cannot be entered due to transition from lower to higher state (the drive might be controlled locally 
and reject an application IF state switch), an error will be generated on EtherCAT. The state transition time out wait time is 3 
seconds.

EtherCAT state

Event

Description

INIT

State

SDO access possible against the drive.

PREOP

State

• SDO access possible against the drive.
• No ctrl data is mapped against the drive.
• Only drive status is mapped on resp registers to service the DSP emergency services.

SAFEOP

State

• SDO access possible against the drive.
• Input PDO data from “Drive 

→

 Option” valid.

• Master output data “Option 

→

 Drive” not valid.

OP

State

• SDO access possible against the drive.
• Input PDO data from “Drive 

→

 Option” valid.

• Master output data “Option 

→

 Drive” valid.

PREOP 

→

 SAFEOP

Trans

• Option will re-map required drive registers in NOID.
• Option will trigger INIT request to re-map ctrl/resp registers exchanged in Online-DRV.

SAFEOP 

→

 PREOP

SAFEOP 

→

 INIT

OP 

→

 PREOP

OP 

→

 INIT

Trans

• If drive is operating, option will trip drive with bUS error.
• Option will trigger NOID to switch operation mode to Online-PRG.
• Option will remap and clear all ctrl/resp data.

SAFEOP 

→

 OP

Trans

NOID will SET “ctrl data valid bit”

OP 

→

 SAFEOP

Trans

No processing done, only bUS error is set against the drive.

INIT

Pre-Operational

Safe-Operational

Operational

Power ON

(IP)

(PI)

(SP)

(PS)

(OP)

(OI)

(SI)

 

(SO)

(OS)

Содержание SI-ES3































































Отзывы:

Нет отзывов