YASKAWA SI-ES3 Скачать руководство пользователя страница 39

Страница: 39 / 62

8 Object Dictionary

YASKAWA ELECTRIC

SIEP C730600 64A 1000-Series Option SI-ES3 Technical Manual

2260 (Hex) - Analog Input Monitor A3

This object can be used to display the analog input A3 level; 100% when input is 10 V.

2270 (Hex) - Drive DI Input

This object can be used to display the input terminal status.

4000 (Hex) - Option NVS FATAL Record

Internal FATAL NVS record for debugging purposes.

Note:

Writing 0xFB to sub-index 0 will clear the record in NVS memory.

4001 (Hex) - Option Info + Status Record

Provides general information of option system firmware parts and internal system states.

Index

(Hex)

Subindex

Content

Default

Access

PDO

Mapping

Value Range

2260

–

Analog input monitor A3

–

Read Only

–

Value

0.1%

Read Only

Unsigned 16

MEMOBUS/Modbus register address of

content

0050 (Hex)

Read Only

Unsigned 16

Value (MEMOBUS/Modbus register): 0x0050 (Terminal A3 Input Level)

Index

(Hex)

Subindex

Content

Default

Access

PDO

Mapping

Value Range

2270

–

Drive DI input

–

Read Only

–

Value

–

Read Only

Unsigned 16

MEMOBUS/Modbus register address of

content

0049 (Hex)

Read Only

Unsigned 16

Value (MEMOBUS/Modbus register): 0x0049 (Input Terminal Status)

Index

(Hex)

Subindex

Content

Default

Access

PDO

Mapping

Value Range

4000

–

Option NVS FATAL record

–

Read/Write

Unsigned 8

Information regarding a system failure/crash is stored in this object and can be read out for on-site troubleshooting.

Number of FATALs

–

Read Only

Unsigned 16

Total number of FATAL events logged since entry was cleared.

Index

(Hex)

Subindex

Content

Default

Access

PDO

Mapping

Value Range

4001

–

Option Info+Status Record

–

Read Only

Unsigned 8

Provides general information of option system firmware parts and internal system states.

OptBootFwRev

–

Read Only

Unsigned 32

Boot firmware revision in flash.
Value: 0x00AABBCC
AA = Major revision
BB = Minor revision
CC = Build

OptAppFwRev

–

Read Only

Unsigned 32

Application firmware revision in flash.
Value: 0x00AABBCC
AA = Major revision
BB = Minor revision
CC = Build

OptRunTimeMS

–

Read Only

Unsigned 32

Total running time in milliseconds of option system since power-up.

NOISystem: iSysErrorBits

–

Read Only

Unsigned 16

NOI System active error bits.

NOISystem: iSysErrorBitsLatched

–

Read Only

Unsigned 16

All errors that have occurred since NOI System start-up.

Содержание SI-ES3































































Результаты поиска

Содержание SI-ES3

Отзывы:

YASKAWA SI-ES3, Техническое руководство, Страница: 39 / 62

Результаты поиска

Содержание SI-ES3

Отзывы: